Tabla de contenido
Publicidad
Impor tant
S
afety Instructions
Save these
instructions
Read
all instructions
before using this
product
3MrM PolygunrM EC Adhesive
Applicator
Operation and Servicing
a
A
Caution
Allow
applicator to cool to room temperature before
servicing. Failure to do
so
may
cause
burns.
fi
Caution
Avoid
contact
with hot
adhesive
and
applicator tip.
May
cause
burns.
Wear safety
glasses
when using.
7\
Caution
Use
only
the
proper temperature module for
the
3M
QuadrackrM-shaped adhesive
used.
Failure to
do
so
may
cause
burns or damage applicator.
Refer to Table
1
for
proper
module selections
for
3M
Quadrack-shaped
adhesives.
A
Caution
Do not pull
adhesive
cartridge from the rear of
the
applicator while in operation. Removing adhesive
from
the
rear
may
cause
molten adhesive to
flow
out the rear of the applicator which may cause
burns and damage the applicator.
3M
Jet-meltrM Adhesive
Note:
For health
and
safety
information,
see
product label
and
Material
Safety Data
Sheet
for
Jet-melt
Adhesive before using.
Use
only 3M-specified
replacement parts. Use
of
other replacement parts
may
cause
hazardous
conditions or damage the applicator.
I
wlnNrNc
To reduce the
risk of electrical shock or
injury
while
operating
or servicing the 3M Polygun EC
Adhesive
Applicator, observe the following safety
rules:
1.
Operate and service the
applicator only
as
described
in this
manual.
2. Connect the applicator only to
a
properly
grounded outlet.
3.
Do not unplug the applicator by pulling on the
cord. Grasp
the
plug, not the cord, to unplug.
4. Do not handle the plug or applicator with wet
hands.
5.
Do not
use
the
applicator outdoors or on wet
surfaces.
6.
Do not
use
the
applicator
if
the
cord or plug is
damaged.
7.
Do not
use
the
applicator
if it
is not working
properly or
has been
damaged, submerged
in
water
or
left
outdoors.
I
wani,lrxc
Use
only 3-prong
grounded
plug
and
properly
grounded
outlet. Failure to
use
properly grounded
plug and outlet may cause electrical shock.
If
you
are
not
sure
ofproper
connections, get help
from
a
qualified electrician or service
person.
I
wanNrNc
Disconnect electrical power
and
make
sure
applicator
has
cooled
to room temperature before
servicing. Failure to disconnect electrical power or
failure to allow applicator to cool before servicing
may
cause
electrical shock or burns.
Read
owner's manual before servicing.
I
wanNrNc
Use
only with 3M
Quadrack-shaped
Jet-melt
adhesive cartridges. Use
with
any other materials
may
cause
hazardous conditions.
A
wlnNrNc
Do not
use an
unapproved extension
cord with the
applicator. Use
of
an
unapproved extension cord
may
cause
electrical shock.
I
wnnNINc
Do not
clean
or remove the 3M Jet-melt Adhesive
with
solvent.
May
cause
fire.
For additional health
and safety
information,
see
the
product label
and
Material
Safety Data
Sheet
for
the
Jet-melt
Adhesive
used.
I
wanNrNc
@
3M
1996
1
Publicidad
Tabla de contenido
