Descargar Imprimir esta página

EINHELL GC-PC 2040/1 Manual De Instrucciones Original página 34

Ocultar thumbs Ver también para GC-PC 2040/1:

Publicidad

Idiomas disponibles

Idiomas disponibles

Cleaning the air fi lter (Fig. 15A/15B)
1. Remove the top cover (14) by undoing the co-
ver fastening screw (A) on the cover. You can
then remove the cover (Fig. 15A).
2. Lift out the air fi lter (15) (Fig. 15B).
3. Clean air fi lter. Wash fi lter in clean, warm,
soapy water. Rinse in clear, cool water. Air dry
completely.
Note: It is advisable to have a supply of spare
fi lters.
4. Insert the air fi lter. Install the air fi lter cover
(14). Make sure that the cover fi ts perfectly
when you do so. Tighten the cover fastening
screw.
7.2.2 Fuel fi lter
Note:Never use the saw without a fuel fi lter. After
100 hours in operation the fuel fi lter should be
cleaned or, in case of damage, replaced. Be sure
to empty the fuel tank before changing the fi lter.
1. Remove the fuel tank cap.
2. Bend a piece of soft wire.
3. Reach into fuel tank opening and hook fuel
line. Carefully pull the fuel line toward the ope-
ning until you can reach it with your fi ngers.
Note: Do not pull hose completely out of tank.
4. Lift fi lter out of tank .
5. Pull off the fi lter with a twist and clean it; if the
fi lter is damaged, dispose of it.
6. Insert a new fi lter. Place one end of the fi lter
into the tank opening. Make sure that the fi lter
is seated in the lower corner of the tank. If ne-
cessary, use a long screwdriver to move the
fi lter to its correct position, taking care not to
damage in the process.
7. Fill tank with fresh fuel / oil mixture. See Sec-
tion Fuel and Lubrication. Install fuel cap.
7.2.3 Spark plug (Fig. 15A-15C)
Note: To ensure that the saw's engine retains its
power, the spark plug must be clean and have the
correct electrode gap (0.6 mm). The spark plug
must be cleaned or replaced after every 20 hours
of service.
1. Set the On/Off switch to Stop (0)".
2. Remove the top cover (14) by undoing the co-
ver fastening screw (A) on the cover. You can
then remove the cover (Fig. 15A).
3. Lift out the air fi lter (15) (Fig. 15B).
4. Disconnect the ignition cable (C) from the
spark plug by pulling and twisting it simultane-
Anl_SA_GC_PC_2040_1_SPK8.indb 34
Anl_SA_GC_PC_2040_1_SPK8.indb 34
GB
ously (Fig. 15C).
5. Remove the spark plug using a spark plug
wrench.
6. Clean the spark plug with a copper wire brush
or fi t a new one.
7.2.4 Carburetor setting
The carburetor has been set to its perfect adjust-
ment at the factory. If it requires adjusting, take the
saw to your nearest authorized after-sales service
outlet.
7.2.5 Chain bar
Grease the guide rail starwheel after every 10
hours of operation. This is necessary to get
the best performance from your chainsaw.
(Fig. 16) Clean the lube hole, then place the
lube gun (not included) at the hole and pump
grease into the bearing until grease is forced
out.
Clean the groove which the chain runs in as
well as the oil entry hole on a regular basis
using a commercially available cleaning tool.
(Fig. 17A) This is important to ensure optimal
lubrication of the guide rail and chain during
operation.
Remove burrs and sharp edges on the guide
rail (2) by carefully filing them down with a flat
file. (Fig. 17B)
Turn the guide rail (2) around after every 8
hours of operation so that it wears evenly on
the top and bottom.
Oil passages
Oil passages on the bar should be cleaned to en-
sure proper lubrication of the bar and chain during
operation.
Note: The condition of the oil passages can be
easily checked. If the passages are clear, the
chain will automatically give off a spray of oil
within seconds of starting the saw. Your saw is
equipped with an automatic oiler system.
Automatic chain lubrication.
The chain saw is equipped with an automatic oil
lubrication system with a toothed wheel drive. It
automatically supplies the bar and the chain with
the right quantity of oil. The moment the engine is
accelerated, the oil also starts to fl ow through the
bar plate more quickly as well.
The chain lubrication system has been set to its
perfect adjustment at the factory. If it requires
adjusting, take the saw to your nearest authorized
after-sales service outlet.
- 34 -
10.01.2017 09:20:27
10.01.2017 09:20:27

Publicidad

loading