Publicidad
Idiomas disponibles
Idiomas disponibles
Attaching the Auxiliary Handle (Fig. A)
WARNING: This handle SHOULD BE USED AT ALL
TIMES to maintain complete control of the tool.
Always make sure the handle is tight.
Screw the auxiliary handle
5
threaded mounting holes of the gear case.
Guards
CAUTION: Guards must be used with all grinding
wheels, cutting wheels, sanding flap discs,
wire brushes, and wire wheels. The tool may
be used without a guard only when sanding with
conventional sanding discs. Refer to Figure A to see
guards provided with the unit. Some applications may
require purchasing the correct guard from your local
dealer or authorized service center.
nOTE: Edge grinding and cutting can be performed with
Type 27 wheels designed and specified for this purpose;
0.25" (6.35 mm) thick wheels are designed for surface
grinding while thinner Type 27 wheels need to be examined
for the manufacturer's label to see if they can be used for
surface grinding or only edge grinding/cutting. A Type 1/41
guard must be used for any wheel where surface grinding
is forbidden. Cutting can also be performed by using a
Type 41 wheel and a Type 1/41 guard.
nOTE: See the Accessories Chart to select the proper
guard / accessory combination.
Mounting and Removing Guard
(Type 1 and Type 27)
Mounting guard (Fig. C)
1. Open the guard release lever
the guard
11
with the slots on the gear case cover.
2. Push the guard down until the guard lugs engage and
rotate freely in the groove on the gear case hub.
3. With the guard latch open, rotate the guard into the
desired working position. The guard body should be
positioned between the spindle and the operator to
provide maximum operator protection.
4. Close the guard latch to secure the guard on the gear
case cover. You should not be able to rotate the guard
by hand when the latch is closed. Do not operate
the grinder with a loose guard or the clamp lever in
open position.
Fig. C
7
tightly into one of the
7
, and align the lugs on
11
Removing guard (Fig. D)
To remove the guard, open the guard latch, rotate the
guard so that the lugs on the guard are aligned with the
slots on the gear case cover, and pull the guard away from
the gear case cover.
nOTE: The guard is pre-adjusted to the diameter of the gear
case hub at the factory. If, after a period of time, the guard
becomes loose, tighten the adjusting screw
in the closed position and guard installed on the tool.
Fig. D
12
CAUTION: Do not tighten the adjusting screw with
the latch in the open position. Undetectable damage
to the guard or the mounting hub may result. If the
guard cannot be tightened by the guard latch, do not
use the tool and take the tool and guard to a service
center to repair or replace the guard.
Flanges and Wheels
CAUTION: Turn unit off and unplug the tool before
making any adjustments or removing or installing
attachments or accessories.
Mounting Non-Hubbed Wheels (Fig. E, F)
WARNING: Failure to properly seat the flanges and/or
wheel could result in serious injury (or damage to the
tool or wheel).
CAUTION: Included flanges must be used with
depressed center Type 27/42 grinding wheels and
Type 1/41 cutting wheels. See the Accessories Chart
for more information.
WARNING: A closed, two-sided cutting wheel guard
is required when using abrasive cutting wheels or
diamond coated cutting wheels.
WARNING: Use of a damaged flange or guard or fail-
ure to use proper flange and guard can re sult in injury
due to wheel breakage and wheel contact. See the
Accessories Chart for more information.
Depressed center Type 27 grinding wheels must be used
with included flanges.
1. Place the tool on a table, guard up.
2. Install the unthreaded backing flange
with the raised center (pilot) facing the wheel.
3. Place wheel
against the backing flange,
13
centering the wheel on the raised center (pilot) of the
backing flange.
English
12
with latch
3
on spindle
1
7
Publicidad
