Descargar Imprimir esta página

EINHELL 45.139.27 Manual De Instrucciones Original página 17

Taladro atornillador con batería
Ocultar thumbs Ver también para 45.139.27:

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 83
All LEDs blink:
The battery temperature is too low. Remove the
battery from the equipment, keep it at room tem-
perature for one day. If the fault reoccurs, this me-
ans that the rechargeable battery has undergone
exhaustive discharge and is defective. Remove
the battery from the equipment. Never use or
charge a defective battery.
6.7 LED lamp (Fig. 6 / Item 9)
The LED lamp (9) can be used in poor lighting
conditions to illuminate the area where you want
to drill or screw. The LED lamp (9) will be lit au-
tomatically as soon as you press the ON/OFF
switch (4).
6.8 Changing the tool (Fig. 7)
Important. Set the changeover switch (3) to its
centre position whenever you carry out any work
(for example changing the tool, maintenance
work, etc.) on the cordless screwdriver.
Open the chuck (8). The chuck opening (a)
must be large enough to hold the tool (drill bit
or screwdriver bit).
Select the suitable tool. Push the tool as far
as possible into the chuck opening (a).
Tighten the chuck (8) and then check that the
tool is secure.
6.9 Screwdriving
It is advisable to use self-centering screws (e.g.
cross recessed head) as these will enable you to
work safely and reliably. Always make sure that
the bit used is of the same size and shape as the
screw. Set the torque to suit the screw size as
specifi ed in the instructions.
7. Cleaning, maintenance and
ordering of spare parts
Danger!
Always pull out the battery pack before starting
any cleaning work.
7.1 Cleaning
Keep all safety devices, air vents and the
motor housing free of dirt and dust as far as
possible. Wipe the equipment with a clean
cloth or blow it with compressed air at low
pressure.
We recommend that you clean the device
immediately each time you have finished
using it.
Anl_TC_CD_18_35_Li_4513927_SPK13.indb 17
Anl_TC_CD_18_35_Li_4513927_SPK13.indb 17
GB
Clean the equipment regularly with a moist
cloth and some soft soap. Do not use
cleaning agents or solvents; these could at-
tack the plastic parts of the equipment. Ensu-
re that no water can seep into the device. The
ingress of water into an electric tool increases
the risk of an electric shock.
7.2 Maintenance
There are no parts inside the equipment which
require additional maintenance.
7.3 Ordering spare parts and accessories
Please provide the following information when
ordering spare parts:
Type of unit
Article number of the unit
ID number of the unit
Spare part number of the required spare part
For our latest prices and information please go to
www.Einhell-Service.com
Tip! For good results we
recommend high-quality ac-
cessories from
www.kwb.eu
welcome@kwb.eu
8. Disposal and recycling
The equipment is supplied in packaging to pre-
vent it from being damaged in transit. The raw
materials in this packaging can be reused or
recycled. The equipment and its accessories are
made of various types of material, such as metal
and plastic. Never place defective equipment in
your household refuse. The equipment should
be taken to a suitable collection center for proper
disposal. If you do not know the whereabouts of
such a collection point, you should ask in your
local council offi ces.
9. Storage
Store the equipment and accessories out of
children's reach in a dark and dry place at above
freezing temperature. The ideal storage tempe-
rature is between 5 and 30 °C. Store the electric
tool in its original packaging.
- 17 -
!
18.01.2022 09:21:48
18.01.2022 09:21:48

Publicidad

loading

Este manual también es adecuado para:

Tc-cd 18/35 li-soloTc-cd 18/35 li