Publicidad
Idiomas disponibles
Idiomas disponibles
WARNING
Recharge only with the
charger specified for the battery. For specific
charging instructions, read the operator's
manual supplied with your charger and
battery.
Inserting/Removing Battery Pack
Insert the battery pack by sliding it into the bat-
tery bay.
To remove the battery pack, pull the battery pack
off of the bay.
Low Battery Indicator
When the radio is powered by a battery pack, a low
battery indicator will be displayed when the battery
pack needs to be charged.
Battery Pack Protection
To protect the life of the battery pack, the radio will
shut off when the battery's charge becomes too
low. If this happens, remove the battery pack and
charge it according to the charger's instructions.
Installing an Auxiliary Device
Open the Auxiliary Compartment to connect an
MP3 player, CD player, or other audio device using
the stereo auxiliary jack. Small devices (less than
3-1/4" wide, 7-1/4" high, and 1-1/8" thick) can be
stored in the compartment during use.
USB Power Outlet
This jack can be used to charge a cell phone,
power a CD player or any other device that uses
less than 2.1 A of DC electrical current. Function
will only occur when the radio is plugged into an
outlet, or the radio is on and an M18™ battery pack
is inserted. The USB Power Outlet will not function
off of a battery pack with the radio off.
NOTE: Any device that uses more than 2.1 A of DC
electrical current will trip a self-resetting function
and disable the output.
WARNING
Always remove battery
pack before changing or removing acces-
sories. Only use accessories specifically
recommended for this radio. Others may be
hazardous.
WARNING
To reduce the risk of fire
or electric shock, do not expose this radio to
rain or moisture.
ASSEMBLY
WARNING
Batteries may leak chemi-
cals or may explode if used incorrectly. The
following care should be taken to prevent
such an incident:
• Make sure the positive (+) and negative (-)
battery terminals are positioned correctly.
• Do not mix new and old batteries together,
or mix different types of batteries.
• Do not try to recharge non-rechargeable
batteries.
If chemicals from the batteries come in
contact with your skin, wash them off imme-
diately with water. If chemicals leak onto the
radio, clean the radio completely.
Changing Back-up Batteries
To hold station presets and clock time when the
battery pack is removed and the radio is unplugged,
2 AAA batteries are re-
quired.
1. Remove battery pack
and unplug radio.
2. Remove the screw
and battery cover.
3. Insert two (2) AAA
batteries according
to matching positive
(+) and negative (-)
marks.
4. Replace the battery
cover and screw.
OPERATION
Turning On/Off and Volume Control
Plug the cord into an appropriate AC outlet or install
an M18™ battery pack.
Turn the On/off / Volume
knob to control the
power and sound functions.
Setting the Clock
1. Press and hold the CLOCK button until the hour
begins to flash.
2. Use the
buttons to change the hour.
3. Press the CLOCK button again. Use the
to change the minutes.
4. Press the CLOCK button again to save.
6
EQ Adjustment
To manually adjust the Bass/Treble sound, press
the EQ button. Set the bass sound using the
buttons. Press the EQ button again to set the treble
sound, using the
buttons.
Selecting Band
Push the MODE button to select AM, FM, or AUX.
Tuning (Seeking and Scanning)
Press and hold the
buttons to SEEK through
the band. When a station is found, the SEEK will
stop. Use the SCAN button to continue through the
stations, pausing at each.
PRESET Stations
To set the PRESET stations:
1. Tune to desired station.
2. Press and hold the PRESET button until the
PRESET indicator on the display begins to flash.
3. Use the
buttons to select the PRESET
location for the station. Five locations (1-5) are
available.
4. Press the PRESET button to save the location.
To tune to a PRESET station:
Press and release the PRESET button to step
through the PRESET stations.
Using the Stereo AUX Jack
1. Open the Auxiliary Compartment.
2. Plug the auxiliary device into the Stereo AUX
jack.
3. Use the MODE button to select AUX.
4. Start the auxiliary device.
MAINTENANCE
WARNING
To reduce the risk of injury,
always unplug the charger and remove the
battery pack from the charger or tool before
performing any maintenance. Never disas-
semble the tool, battery pack or charger.
Contact a MILWAUKEE service facility for
ALL repairs.
Maintaining Tool
Keep your tool, battery pack and charger in good
repair by adopting a regular maintenance program.
If the tool does not start or operate at full power
with a fully charged battery pack, clean the contacts
on the battery pack. If the tool still does not work
properly, return the tool, charger and battery pack,
to a MILWAUKEE service facility for repairs.
WARNING
To reduce the risk of per-
sonal injury and damage, never immerse your
tool, battery pack or charger in liquid or allow
a liquid to flow inside them.
Cleaning
Clean dust and debris from charger and tool
vents. Keep tool handles clean, dry and free of oil
or grease. Use only mild soap and a damp cloth
to clean the tool, battery pack and charger since
certain cleaning agents and solvents are harmful to
plastics and other insulated parts. Some of these
include gasoline, turpentine, lacquer thinner, paint
thinner, chlorinated cleaning solvents, ammonia
and household detergents containing ammonia.
Never use flammable or combustible solvents
around tools.
Repairs
For repairs, return the tool, battery pack and char-
ger to the nearest service center listed on the back
cover of this operator's manual.
ACCESSORIES
WARNING
Always remove battery
pack before changing or removing acces-
sories. Only use accessories specifically
recommended for this tool. Others may be
hazardous.
For a complete listing of accessories refer to your
MILWAUKEE Electric Tool catalog or go online
to www.milwaukeetool.com. To obtain a catalog,
contact your local distributor or a service center.
7
Publicidad
