Publicidad
Idiomas disponibles
Idiomas disponibles
18 | English
(7)
Locking screw for protective guard
(8)
Mounting flange with O‑ring
a)
(9)
Grinding disc
(10) Clamping nut
(11) Quick-clamping nut
a)
(12) Carbide grinding head
(13) Protective guard for cutting
a)
(14) Cutting disc
Technical Data
Angle grinder
Article number
Rated power input
Power output
Rated speed
Max. grinding disc diameter
Grinding spindle thread
Max. thread length of grinding
spindle
Restart protection
Weight according to EPTA-Procedure 01:2014
– with low-vibration auxiliary
handle
– with standard auxiliary handle
Protection class
The specifications apply to a rated voltage [U] of 230 V. These specifications may vary at different voltages and in country-specific models.
Noise/Vibration Information
Noise emission values determined according to
EN 60745-2-3.
Typically the A-weighted noise level of the power tool are: 93
dB(A); sound power level 104 dB(A). Uncertainty K = 3 dB.
Wear hearing protection!
Vibration total values a
(triax vector sum) and uncertainty K
h
determined according to EN 60745-2-3:
Surface grinding (roughing):
2
2
a
= 7.5 m/s
, K = 1.5 m/s
,
h
Disc sanding:
2
2
a
= 7.5 m/s
, K = 1.5 m/s
.
h
The vibration level given in these instructions has been
measured in accordance with a standardised measuring pro-
cedure and may be used to compare power tools. It can also
be used for a preliminary estimation of exposure to vibra-
tion.
The stated vibration level applies to the main applications of
the power tool. However, if the power tool is used for differ-
ent applications, with different application tools or poorly
maintained, the vibration level may differ. This can signific-
antly increase the exposure to vibration over the total work-
ing period.
1 609 92A 6FB | (19.02.2021)
(15) Hand guard
(16) Rubber sanding pad
(17) Abrasive disc
(18) Round nut
a)
(19) Cup brush
(20) Handle (insulated gripping surface)
a)
a) Accessories shown or described are not included with the
W
W
-1
min
mm
mm
kg
kg
To estimate the exposure to vibration accurately, the times
when the tool is switched off or when it is running but not ac-
tually being used should also be taken into account. This can
significantly reduce the exposure to vibration over the total
working period.
Implement additional safety measures to protect the oper-
ator from the effects of vibration, such as servicing the
power tool and application tools, keeping the hands warm,
and organising workflows correctly.
Fitting
Fitting Protective Equipment
u
Note: If the grinding disc breaks during operation or the
holding fixtures on the protective guard/power tool become
damaged, the power tool must be sent to the after-sales ser-
vice immediately; see the "After-Sales Service and Applica-
tion Service" section for addresses.
Protective guard for grinding
Place the protective guard (6) on the spindle collar. Adjust
the position of the protective guard (6) to meet the require-
ments of the operation. Lock the protective guard (6) by
a)
a)
a)
a)
a)
product as standard. You can find the complete selection of
accessories in our accessories range.
GWS 900
3 601 C96 00A
900
450
11.000
115
M 14
22
●
2.0
1.9
/ II
Pull the plug out of the socket before carrying out any
work on the power tool.
GWS 900
3 601 C96 009
900
450
11.000
125
M 14
22
●
2.0
1.9
/ II
Bosch Power Tools
Publicidad
