EINHELL CC-JS 18 Manual De Instrucciones Original página 15

kind resulting from such misuse.
Please note that our equipment has not been de-
signed for use in commercial, trade or industrial
applications. Our warranty will be voided if the
equipment is used in commercial, trade or indust-
rial businesses or for equivalent purposes.
4. Technical data
Jump start power bank
Li-Po battery: ......................................... 66.6 Wh
Charging time approx. ................................... 6 hr
USB d.c. voltage outlet: ................... 5 V max. 1 A
USB d.c. voltage outlet: ................... 5 V max. 2 A
d.c. voltage outlet: ...................... 19 V max. 3.5 A
d.c. voltage outlet: ....................... 12 V max. 10 A
Jump starting current: .........................................
................................. 300 A (5 sec) / 600 A (max.)
Ambient temperature for jump starting: ...............
.................................................... + 15°C - + 40°C
Charger
Nominal input voltage: ....... 100-240 V ~50/60 Hz
Nominal output voltage: ........................ 15 V DC
Nominal output current: .................................. 1 A
5. Before starting the equipment
5.1 Charging the jump start power bank with
the supplied charger
The following applies to the charger:
This equipment can be used by children of 8 ye-
ars and older and by people with limited physical,
sensory or mental capacities or those with no ex-
perience and knowledge if they are supervised or
have received instruction in how to use the equip-
ment safely and understand the dangers which
result from such use. Children are not allowed
to play with the equipment. Unless supervised,
children are not allowed to clean the equipment
and carry out user-level maintenance work.
Before you connect the equipment to the power
supply make sure that the data on the rating plate
are identical to the supply voltage.
Important! Pull out the power plug before making
adjustments to the equipment. Charge the equip-
ment only with the charger supplied.
Observe the enclosed safety information with de-
Anl_CC_JS_18_SPK7.indb 15 Anl_CC_JS_18_SPK7.indb 15
GB
tailed information about charging.
The outlets must not be used while charging is in
progress.
•
Connect the supplied charger (Fig. 2a / Item
10) to the „15V 1A input" charging jack (Fig. 1
/ Item 6) on the equipment.
•
Plug the charger into the socket outlet and
the battery will be charged. The LED (Fig. 1/
Item 7) shine (flash) during charging and in-
dicate the charging status. When charging is
finished, all the LED shine.
•
The time it takes to fully recharge an empty
battery is approximately 6 hours. The tem-
perature of the battery pack may rise slightly
during the charging operation. This is normal.
5.2 Charging the jump start power bank with
the 12 V cigarette lighter cable
Charging should be performed only while driving,
as the vehicle's battery is discharged in the pro-
cess. Place the equipment in a suitable location
where it cannot move in response to an abrupt
change in speed and/or direction.
•
Connect the supplied 12 V cigarette lighter
cable (Fig. 2b / Item 11) to the „15V 1A input"
charging jack (Fig. 1 / Item 6) on the equip-
ment.
•
Plug the 12 V connector into a suitable 12 V
cigarette lighter socket.
5.3 Battery capacity indicator
Press the ON/OFF button (Fig. 1/Item 5) briefl y.
The LED for the battery capacity indicator (Fig. 1
/ Item 7) light up. The number of LED that are lit
indicate the current charge level of the integrated
Li-Po battery.
100% charged = 5 LED steady on
<10% charged = no LED
6. LED lamp
Caution! Do not look into the light beam.
•
Press the ON/OFF button for 3 seconds – the
LED lamp (Fig. 1 / Item 4) will be permanently
lit.
•
Press the ON/OFF button again – the LED
lamp will be lit as a „strobe light".
•
Press the ON/OFF button again – the LED
lamp will be lit as an „SOS" Morse code sig-
nal lamp.
- 15 -
08.01.16 11:32 08.01.16 11:32