Descargar Imprimir esta página

EINHELL GC-MT 2560 LD Manual De Instrucciones Original página 20

Ocultar thumbs Ver también para GC-MT 2560 LD:

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 73
Assembling the steering handle, clutch lever
and start/stop lever
1. Arrange the components properly as descri-
bed in section 2.1 Layout.
2. Fit the steering handle holder (20) as shown
in Fig. 5c/5d.
3. Fit the steering handle clutch lever (21) and
the steering handle start/stop lever (22) as
shown in Fig. 5e.
4. Fit the cross strut (23) as shown in Fig. 5f.
5. Fitting the clutch lever (24) is easy if you ob-
serve the following steps:
- Push the Bowden wire sleeve (Fig. 5g/Item
A) into the eyelet (Fig. 5g/Item B). Adjust the
Bowden wire to maximum length by turning
the lock nuts.
- Attach the Bowden wire (Fig. 5h/Item C) to
the clutch lever (24) and fi t the clutch lever
to the steering handle. Check that the safety
lever is correctly seated. Carry out a function
test. Pull the safety lever (25) to the clutch
lever as shown in Fig. 6d. The clutch lever will
be released and can be actuated.
6. Adjust the length of the actuator cable as de-
scribed in section 7.2.4.
7. Fit the start/stop lever (26) as shown in Fig. 5i.
8. Fit the cable clip (39) as shown in Fig. 5k.
Caution! You must fi ll in engine oil and fuel before
you start up for the fi rst time.
Check the fuel and engine oil levels and top
up if required.
Make sure that the ignition cable is secured to
the spark plug.
Check the area immediately around the pow-
er cultivator.
6. Operation
Set the depth stop (Fig.4e/Item 15) to the
desired depth and secure with the split pin.
Swing up the transport wheel and make sure
that the bolt of the latch is engaged in the
mount at the front (Fig. 6a-6b).
You can adjust the steering handle to your
physical size. To do so, undo the screws(Fig.
6c), adjust the bracket and retighten the
screws.
To start the star-type hoes, pull up the safety
lever (25) and press and hold down the clutch
lever (24) (Fig.6d). Releasing the clutch lever
will bring the star-type hoes to a stop (if they
do not stop, readjust the clutch cable).
GB
Starting the engine
1. Ensure that the ignition cable is connected to
2. Stand behind the power cultivator. Move the
3. Start the engine using the reversing starter
Note! Never allow the actuator cable to snap
back.
Note! In cold weather, it may be necessary to re-
peat the starting process several times.
Stopping the engine
Move the engine start/stop lever (26) into the
STOP position.
7. Cleaning, maintenance, storage
Danger!
Pull out the spark plug boot before doing any
cleaning and maintenance work.
7.1 Cleaning
7.2 Maintenance
Please note: Switch off the unit immediately
and contact an authorized dealer:
- 20 -
www.sidirika-nikolaidi.gr
the spark plug.
engine start/stop lever (Fig.7/Item 26) to posi-
tion I I. If the engine has already warmed up,
move the engine start/stop lever to the „Hare"
position.
(Fig. 1/Item 2). To do this, pull out the handle
by approx. 10-15 cm (until you feel a resis-
tance) and then start the engine with a sharp
tug.
and ordering of spare parts
Keep all safety devices, air vents and the
motor housing free of dirt and dust as far as
possible. Wipe the equipment with a clean
cloth or blow it with compressed air at low
pressure.
We recommend that you clean the device
immediately each time you have finished
using it.
Clean the equipment regularly with a moist
cloth and some soft soap. Do not use
cleaning agents or solvents; these could
attack the plastic parts of the equipment. En-
sure that no water can seep into the device.
In the event of unusual vibrations or noise.
If the engine appears to be overloaded or
misfires.

Publicidad

loading

Este manual también es adecuado para:

34.302.81