Metabo SBE 701 SP Manual Original página 15

8.11 Unscrew the chuck (when driving screws
without the chuck or for use with attach-
ments) Fig. L, M, or N
Note for Fig. M, N: Release by tapping lightly with a
rubber hammer, as shown, and unscrew.
Note: If a bit clamping bush (order no. 6.31281) is
attached, the screwdriver bit inserted in the
hexagon socket of the spindle is held in place.
9. Cleaning, Maintenance
Keyless chuck cleaning:
After prolonged use hold the chuck vertically, with
the opening facing down, and fully open and close it
several times. The dust collected falls from the
opening. The application of cleaning spray to the
jaws and jaw openings at regular intervals is recom-
mended.
10. Troubleshooting
Electronic signal display (10):
Rapid flashing - restart protection
(SBE 1000, SBE 1100 Plus)
When power is restored after a power failure, the
machine - which is still switched on - will not start for
safety reasons. Switch machine on and off again.
Slow flashing - carbon brushes worn
(SBE 1100 Plus, SBE 1300)
The carbon brushes are almost completely worn. If
the brushes are completely worn, the machine
switches off automatically. Have the brushes
replaced by an authorized service centre.
Permanently lit - overload (SBE 1100 Plus)
If the machine is subject to long periods of contin-
uous overloading, the power input of the machine is
limited. This prevents the further unauthorized
heating of the motor.
11. Accessories
Use only genuine Metabo accessories.
Use only accessories which fulfil the requirements
and specifications listed in these operating instruc-
tions.
Fit accessories securely. Secure the machine if it is
operated in a bracket. Loss of control can cause
personal injury.
For a complete range of accessories, see
www.metabo.com or the main catalogue.
12. Repairs
Repairs to electrical tools must be carried out by
qualified electricians ONLY!
If you have Metabo electrical tools that require
repairs, please contact your Metabo service centre.
For addresses see www.metabo.com.
You can download spare parts lists from
www.metabo.com.
13. Environmental Protection
Observe national regulations on environmentally
compatible disposal and on the recycling of disused
machines, packaging and accessories.
Only for EU countries: Never dispose of
power tools in your household waste! In
accordance with European Guideline 2002/
96/EC on used electronic and electric equipment
and its implementation in national legal systems,
used power tools must be collected separately and
handed in for environmentally compatible recycling.
14. Technical Specifications
Fig. O. We reserve the right to make technical
improvements.
P = Rated input
1
P = Power output
2
n * = No-load speed
1
n * = Load speed
2
max. dia. =Max. solid drill diameter
s max = Max. impact rate
b = Chuck capacity
G = Spindle thread
H = Spindle with hexagon socket
m = Weight
D = D=Collar diameter
Measured values determined in conformity with
EN 60745.
Machine in protection class II
~
Alternating current
The technical specifications quoted are subject to
tolerances (in compliance with the relevant valid
standards).
* Energy-rich, high-frequency interference can cause
fluctuations in speed. The fluctuations disappear,
however, as soon as the interference fades away.
Emission values
Using these values, you can estimate the emis-
sions from this power tool and compare these with
the values emitted by other power tools. The actual
values may be higher or lower, depending on the
particular application and the condition of the tool or
power tool. In estimating the values, you should also
include work breaks and periods of low use. Based
on the estimated emission values, specify protective
measures for the user - for example, any organisa-
tional steps that must be put in place.
Vibration total value (vector sum of three directions)
determined in accordance with EN 60745:
a = Vibration emission value (impact drilling
h, ID
into concrete)
a = Vibration emission value
h, D
(drilling into metal)
K ,K =Uncertainty (vibration)
h,ID h,D
Typical A-effective perceived sound levels:
L = Sound pressure level
pA
L = Acoustic power level
WA
K
, K = Uncertainty
pA WA
Wear ear protectors!
ENGLISH en
15