Publicidad
Idiomas disponibles
Idiomas disponibles
Model - Modello - Modèle
Modell - Modelo - Modelo
Constructeur - Fabbricante
Manufacturer - Hersteller
Fabricante - Fabricante
20. ENERGY SAVING TIPS
•
Install the appliance in a dry, well-ventilated room away from heat sources (radiator, cooking surface and so on) and in a position
out of direct sunlight.
•
Follow the installation instructions to ensure adequate ventilation. Insufficient ventilation to the back of the appliance causes an
increase in energy consumption and reduces cooling efficiency.
•
The internal temperature of the appliance depends on the room temperature, how often the doors are opened and where the
appliance is placed. These factors have to be taken into account when setting the thermostat. Only open the doors when strictly
necessary.
•
Let hot food and drink cool down before placing them in the appliance.
•
The positioning of the shelves in the fridge has no effect on energy efficiency.
•
The fridge compartment light system uses a LED light, which at the same time ensures more efficient lighting and reduced energy
consumption.
21. INSTRUCTIONS FOR CORRECT INSTALLATION AND
MAINTENANCE
The user and maintenance instructions are found in the User Manual available on the website www.eptarefrigeration.com.
The installation instructions dedicated to expert personnel are available:
•
From the service network
•
In some product categories in paper form delivered with the product.
22. PROFESSIONAL REPAIR SERVICES
The services are provided by our service network that can be consulted in the contact area at the web address: www.eptarefrigeration.
com.
23. SPARE PARTS
The spare parts and the information to repair the unit are available for at least 8 years after the product is declared out of production
at the following web address: www.epta-service.com/service/.
The credentials are provided on request by sending an email to: servicesupport@eptarefrigeration.com
24. OUTER CLEANING
WARNING! TURN OFF POWER SUPPLY TO THE CABINET BY DISCONNECTING THE POWER
PLUG BEFORE CLEANING.
For a good preservation of the cabinet's body a periodical cleaning is necessary.
1. EXTERNAL BODY:
When necessary, the external body should be cleaned with a cloth and a neutral soap and water solution.
2. STAINLESS STEEL SURFACES:
pads etc. which will spoil the finish of the stainless steel.
3. SURFACES IN PLASTIC MATERIAL:
no circumstances should alcohol, methylated spirits or solvents be used.
4. GLASS SURFACES:
can leave a film of calcium on the surface of the glass.
25. TANK CLEANING
WARNING! TURN OFF POWER SUPPLY TO THE CABINET BY DISCONNECTING THE POWER
PLUG BEFORE CLEANING.
By tank cleaning, proceed as follows:
1.
Place the goods in special refrigerated containers, kept at the same temperature and remove the shelves.
2.
Before cleaning the tank the inside temperature must be equal to the ambient temperatur.
3.
Leave the doors open and begin the operation of tank washing when the tank temperature is the same as the ambient temperature.
4.
Proceed with washing and drying the internal chamber with a cloth using neutral PH detergent and fresh water.
5.
Clean the surfaces with a cloth, using neutral PH detergent, rinse and dry.
6.
Clean the height adjusters supporting the levels with a jet of air.
7.
Avoid water entering into the appliance lighting units.
8.
Then plug the unit and wait till the appliance reaches the right temperature before filling it again.
Do not use any aggressive or abrasive cleaning agents.
Never use a water hose or a high-pressure jet to clean the cabinet.
WARNING! Do not use jet of water to clean the cabinet: electrical wiring could be damaged.
WARNING! Never use mechanical devices or any other means to accelerate the defrosting process,
other than those recommended by the manufacturer.
FIZZ 42
BITTER 42
EPTA S.p.A. - Sede legale
Via Mecenate, 86 - 20138 Milano – Italy
Capitale € 68.515.000 - R.E.A./MI – 1730229
Registro delle Imprese e Cod.Fiscale n. 04160730968
Partita IVA 04160730968
Wash with warm water and mild detergent, rinse well and dry with soft cloth. Avoid scouring
Wash with warm water and mild detergent, rinse well and dry with soft cloth; under
Only use products specifically designed for glass cleaning; It is not advisable to use ordinary water which
1 8 / 6 0
PAGE
N° DOC
Publicidad
