EINHELL TC-MC 355/1 Manual De Instrucciones Original página 15

3. Proper use
The metal cutting-off machine is designed for cut-
ting metal commensurate with the machine's size.
The equipment is to be used only for its prescri-
bed purpose. Any other use is deemed to be a
case of misuse. The user / operator and not the
manufacturer will be liable for any damage or inju-
ries of any kind caused as a result of this.
Please note that our equipment has not been de-
signed for use in commercial, trade or industrial
applications. Our warranty will be voided if the
machine is used in commercial, trade or industrial
businesses or for equivalent purposes.
The machine is to be operated only with suitable
cutting wheels. It is prohibited to use any kind of
saw blade made of HSS, HM, CV, etc. To use the
equipment properly you must also observe the
safety information, the assembly instructions and
the operating instructions to be found in these
operating instructions.
All persons who use and service the equipment
have to be acquainted with these operating
instructions and must be informed about the
equipment's potential hazards. It is also imperati-
ve to observe the accident prevention regulations
in force in your area. The same applies for the
general rules of health and safety at work.
The manufacturer will not be liable for any chan-
ges made to the equipment nor for any damage
resulting from such changes.
Even when the equipment is used as prescribed
it is still impossible to eliminate certain residual
risk factors. The following hazards may arise in
connection with the equipment's construction and
design:
•
Contact with the cutting-off wheel in the unco-
vered cutting zone.
•
Reaching into the cutting-off wheel while it is
running (injuries through cutting).
•
Kick-back of workpieces and parts of work-
pieces.
•
Broken cutting-off wheels.
•
Catapulting of damaged or cutting-off wheels.
•
Damage to hearing if essential ear-muffs are
not used.
Anl_TC_MC_355_1_SPK13.indb 15 Anl_TC_MC_355_1_SPK13.indb 15
GB
4. Technical data
AC motor .................................220-240 V~ 50 Hz
Power P .................................................. 2200 W
Idle speed n .......................................4200 min-¹
0
Cutting-off wheel ......... Ø 355 x Ø 25.4 x 2.8 mm
Base area ...................................... 470 x 280 mm
Swiveling range ...................................... 0° – 45°
Max. vise clamping range ....................... 250 mm
Saw width at 90° .............. Ø 125 / 110 x 110 mm
Saw width at 45° .................. Ø 100 / 90 x 90 mm
Weight ......................................................16.2 kg
Danger!
Sound and vibration
Sound and vibration values were measured in
accordance with EN 62841.
L sound pressure level ..................... 94.1 dB(A)
pA
K uncertainty ............................................. 3 dB
pA
L sound power level ..................... 107.1 dB(A)
WA
K uncertainty ............................................. 3 dB
WA
Keep the noise emissions and vibrations to a
minimum.
•
Only use appliances which are in perfect wor-
king order.
•
Service and clean the appliance regularly.
•
Adapt your working style to suit the appliance.
•
Do not overload the appliance.
•
Have the appliance serviced whenever ne-
cessary.
•
Switch the appliance off when it is not in use.
•
Wear protective gloves.
Caution!
Residual risks
Even if you use this electric power tool in
accordance with instructions, certain resi-
dual risks cannot be rules out. The following
hazards may arise in connection with the
equipment's construction and layout:
1. Lung damage if no suitable protective dust
mask is used.
2. Damage to hearing if no suitable ear protec-
tion is used.
3. Health damage caused by hand-arm vib-
rations if the equipment is used over a pro-
longed period or is not properly guided and
maintained.
- 15 -
22.06.2022 08:25:48 22.06.2022 08:25:48