Publicidad
Idiomas disponibles
Idiomas disponibles
E N G L I S H
HOW TO ASSEMBLE
THE SILICON PLATE FOR IRON
(SEE DRAWING PAGE 10-5 FIG. 3)
Position the silicon part "POS. 33" on the iron rest
"POS. 32".
HOW TO ASSEMBLE THE
PEDAL GROUP
(SEE DRAWING PAGE 10-5 FIG.4)
Proceed in the following way:
a) Assemble the pedal group to the unit frame
fitting the two screws available, in the
corresponding holes located on the frame
itself.
The two sets adjustment holes are to fix the
pedals to the wished distance from the table.
HOW TO FIT THE TABLE COVER
(SEE DRAWING PAGE 10-6)
a) Put the mesh followed by the felt "POS. 35",
making it flush to the buck.
b) Thread the 2 rods A and B into the cloth cover
"POS. 36".
c) Put on the cloth cover "POS. 36" checking
that it is perfectly flush to the board.
d) Hook one edge of the springs to the rod A,
checking that the cords "POS. 40" are not
caught.
e) Hook the second edge of the rod B by running
the springs under the buck and checking that
the cords "POS. 40" are not caught.
f)
Pull at the same time the two ends of the
cords "POS. 40".
HOW TO ASSEMBLE THE
GARMENT TRAY AND THE
GARMENT TRAY COVER CLOTH
(SEE DRAWING PAGE 10-7)
Proceed as follows:
a) Assemble
the garment tray "POS. 35"
C H A P T E R 4
inserting it into the two holes placed under
the finishing board, match the holes between
the garment tray and the machine frame,
then fix it using the two self-threading screws
supplied.
b) Put on the elasticised cloth "POS. 37" on the
garment tray "POS.35".
HOW TO ASSEMBLE THE ARM
(SEE DRAWING PAGE 10-8)
Proceed as follows:
a) Fix the flange of the arm shape "POS. 51" at
the side of the board by means of the 4 issued
bolts "POS. 48".
b) Lubricate the threaded joints: if using the arm
it would have an excessive slack, screw the
arm clockwise (conical threads).
c) Assemble the arm "POS. 53" screwing it
clockwise into the flange "POS. 51".
d) Assemble the shape "POS. 54" screwing it
clockwise in the arm "POS. 53". In case of
heated shape:
Connect the socket "POS. 56" on the rear
side of the frame of the machine and
carry out the electric connection (see
electric circuit).
Put the plug of the heated form "POS
in the socket "POS. 56" and hook them.
Fix the electric cable to the arm "POS
by means of the two springs "POS. 61".
WATER CONNECTION
(SEE DRAWING PAGE 10-11)
Fit a 3/8" zinc-platted gas pipe to within 100 cm
of the machine.
Fit a ball valve with tube connector "POS. 66" to
the end of the tube, and connect it by a rubber
hose (Øint 13 mm) suited to the mains water
pressure to the water input "POS. 14".
In the case of the boiler being feed from a water
tank, request the manufacture for information
regarding the modifications to be made to the
pump. Connect the drainage gate valve "POS. 17"
to the drain using a rigid heat-insulated pipe.
In the case of there not being a drain near by, or
the drainage of hot water not being allowed, use a
15-20 litre tank to collect the boiler waste water
(the water can then be disposed of when it has
cooled).
Page 4-2
E N G L I S H
SHAPE
55"
.
53"
.
Publicidad
