Publicidad
Idiomas disponibles
Idiomas disponibles
Attaching the battery holder
Only when using the battery cartridge used with
battery holder
You can hang the battery holder on your waist belt.
To prevent the battery holder from dropping acciden-
tally, attach a strap using the strap hole and secure it.
► Fig.5: 1. Strap hole
The battery holder has an anti-drop function. When
removing the battery holder from the belt, pull up the
battery holder while pressing the unlock button.
► Fig.6: 1. Unlock button
Installing or removing the fan unit
1.
Open the zip fastener inside the jacket. (Skip this
step if your jacket/vest does not have the lining)
► Fig.7: 1. Zip fastener
2.
Turn the ring counterclockwise and remove it from
the fan unit.
► Fig.8: 1. Fan unit 2. Ring
3.
From the outside of the jacket/vest, insert the
head of the fan unit into the hole in the jacket/vest.
► Fig.9: 1. Fan unit 2. Hole
4.
From the inside of the jacket/vest, place the fan
unit so that the loop on the fan unit comes closest to the
strip on the jacket/vest.
(Do not fasten the snap button on the strip at this step.)
► Fig.10: 1. Strip 2. Loop
5.
From the inside of the jacket/vest, place the ring
onto the fan unit and turn it clockwise until the triangle
marking is aligned with " II " marking.
► Fig.11: 1. Ring 2. Fan unit 3. " II " marking
4. Triangle marking 5. " I " marking
NOTE: When turning the ring, be careful not to move
the fan unit position. Keep the position of the loop on
the fan unit closest to the strip.
NOTE: Put the ring parallel to the fan unit. If not, you
may not be able to turn the ring smoothly.
NOTE: When you use filter set (optional accessory),
turn the ring until the triangle marking is aligned with
" I " marking. (the ring cannot be turned up to " II "
marking)
6.
Pass the strip through the loop on the fan unit and
fasten the snap button.
► Fig.12: 1. Strip 2. Snap button
CAUTION:
Always use the strip and snap
button to secure the fan unit to the jacket/vest. If
the fan unit falls, it may cause an injury, or damage to
the fan unit.
7.
Attach the other fan unit to the jacket/vest in the
same way.
8.
Connect the power cable to the fan units.
► Fig.13: 1. Power cable 2. Cable holder 3. Zip
fastener
NOTE: The zip fastener is not provided with the
jacket/vest without lining.
NOTICE:
Always connect the power cable to
both of the fan units. The fan does not operate if the
power cable is connected to one fan unit only.
9.
Follow either instructions below depending on how
to store the battery when using the fan jacket/vest:
When storing the battery in the battery pocket or on
your belt
Pass the end of the power cable out through the hole
in the jacket's/vest's lining as shown in the figure (skip
this step if your jacket/vest does not have the lining).
Support the cable using the cable holder.
► Fig.14: 1. Hole in the lining 2. Power cable
When storing the battery in the jacket's/vest's
pocket
(Only for the jackets/vests with the hole for direct
access to the pocket)
From the inside of the jacket/vest, pass the end of the
power cable out through the hole in the jacket's/vest's
pocket as shown in the figure.
► Fig.15: 1. Hole in the pocket 2. Power cable
10. Connect the power cable to the battery holder /
Battery BL1055B.
► Fig.16: 1. Battery holder 2. Battery BL1055B
11.
Close the zip fastener.
(Skip this step if your jacket/vest does not have the
lining)
CAUTION:
When using the fan jacket/vest,
securely store the battery in the pocket or hook it
on your belt to prevent it from falling.
Follow the installation procedure in reverse when
removing it.
Attaching the filter set
Optional accessory
The filter set protects the fan unit from dust and powder.
We recommend that you use the filter set in a dusty or
powdery work place.
Install the filter attachment between the fan unit and the
ring. Turn the ring clockwise until the triangle marking is
aligned with " I " marking. After that, attach the filter onto
the filter attachment.
► Fig.17: 1. Ring 2. Hole in the jacket/vest 3. Filter
attachment 4. Fan unit 5. Filter 6. " I " mark-
ing 7. Triangle marking
NOTICE:
Make sure that the filter fully covers
the filter attachment. For better protection against
dust and powder, tuck the skirt of the filter
between the jacket/vest and filter attachment.
13 ENGLISH
Publicidad
