Festool MX 1200/2 E EF Manual De Instrucciones página 14

The stirrer must only be operated with a single-
phase alternating current with a nominal voltage of
220–240 V/ 50/60 Hz. In the 2nd level, the machine
is protected against accidents caused by electrical
current in accordance with the standard EN 60 745-1
and it has built-in radio interference suppression
in accordance with the standard EN 55 014.
Before starting up the machine, check that the
specifi cations on the type plate correspond to the
actual voltage of the power supply.
If required, you can extend the fl exible power ca-
ble as follows:
- Length 20 m, conductor cross-section
2
3×1.5 mm
- Length 50 m, conductor cross-section
3×2.5 mm 2
Only use extension cables that are suitable for
outside use and that are marked accordingly.
Operating with electric generator (EG) with
combustion motor drive
 The manufacturer of the stirrer does not pro-
vide any guarantee for incorrect operation of
the stirrer with any EG.
The stirrer can be operated with an EG if the fol-
lowing conditions are met:
- The output voltage of the EG must always be
within the range of 230 VAC ±10%, the EG must
be equipped with Automatic Voltage Regula-
tion (AVR). The stirrer must not work correctly
without this regulation and may also become
damage.
- The power of the EG must be at least 2.5 times
greater than the connected load of the stir-
rer (i.e. 3 kW for MX 1200/2 E EF, 3.75 kW for
MX 1600/2 E EF)
- If you operate using an EG that does not have
suffi cient power, the speed may fl uctuate and
the power of the machine may decrease
6.8 Stationary use
The stirrer can be clamped into the MS 57 Festool
stirrer stands at the
7 Service and maintenance
CAUTION
Never use a machine that is damaged in any
way! (Damage also includes a ripped or worn
flexible switch protection or clamping ring
protection on the E R G O F I X adapter).
 Have a damaged machine repaired in an au-
thorised Festool workshop.
57 mm collar [1-9].
WARNING
Risk of accident, electric shock
 Always pull the plug out of the socket before
performing any type of work on the machine.
 All maintenance and repair work which re-
quires the motor housing to be opened, must
only be carried out by an authorised service
workshop.
Customer service and repair. Only through
manufacturer or service workshops:
Please fi nd the nearest address at: www.
festool.com/Service
Use only original Festool spare parts! Or-
EKAT
4
der No. at: www.festool.com/Service
5
3
2
1
- The ventilation holes on the motor hood must
not be blocked.
- The machine automatically switches off if the
carbon brushes are worn. The machine must
be sent to the workshop for maintenance work.
- We recommend that you clean the machine
regularly. Remove any dust, residual mixing
material and any other dirt. If you use solvent-
based cleaning agents, these may damage the
painted surfaces or the plastic parts. If you use
these cleaning agents, we recommend that you
test the effect of these agents on a small, con-
cealed area. The ventilation holes on the motor
hood must not be blocked.
- Commission an authorised workshop to
change brushes, the power cable etc.. If the
machine is knocked in any way, it is also nec-
essary to entrust an authorised workshop in
order to prevent any mechanical or electrical
danger arising.
- The packaged machine can be stored in a dry
place without heating as long as the inside
temperature does not fall below −5 °C. The
unpackaged machine must only be stored in
a dry, enclosed space where the temperature
does not fall below +5 °C and where no extreme
temperature fl uctuations occur.
8 Environment
Do not throw the power tool in your household
waste! Dispose of the machine, accessories and
packaging at an environmentally-responsible re-
cycling centre! Observe the valid national regula-
tions.
EU only: European Directive 2002/96/EC stipulate
that used electric power tools must be collected
14