Kinderkraft RINE Manual De Usuario página 16

• To avoid injury ensure that the child is kept away when
unfolding and folding this product.
• Do not let the child play with this product.
• Always use the restraint system.
• Check that the pram body or seat unit or car seat
attachment devices are correctly engaged before use.
• This product is not suitable for running or skating.
•
Age and weight usage: from 0 months up to 22 kg or up to 4 years, whichever comes first.
•
We recommend using lowest reclined position for newborn babies.
•
This product may only be used by one child at the same time
•
The parking device shall be engaged when placing and removing the children
•
The maximum basket load is 2 kg.
•
The maximum load carried in the cup holder must never exceed 0,5 kg.
•
Maximum load in the trinket pocket 0.25 kg.
•
Any load attached to the handle and/or on the back of the backrest and/or on the sides of the vehicle will affect the
stability of the vehicle.
•
Use only parts and accessories supplied or recommended by the manufacturer. Do not use other parts or
accessories.
•
Lift the front suspension when going up a curb or step.
•
Do not place the product near open flame or other heat sources.
•
Do not use with an additional platform.
I. Buggy components (FIG. 1)
A. Seat frame and safety straps
B. Front wheels
C. Rear wheels
II. UNFOLDING BUGGY FRAME
Place the frame on a flat surface with its handle up (FIG. 2). In order to unfold the frame, move the lock (FIG. 2.I) on the
right side of the buggy and lift the frame until you hear the locking sound (FIG. 2.II). A properly unfolded frame is shown
in FIG. 3.
III. WHEEL ASSEMBLY/DISASSEMBLY
Insert the rear wheels into the slot in the rear axle until they are entirely blocked (FIG. 4). In order to remove the rear
wheels, unlock the locking button located on both sides of the rear axle (FIG. 5.I) while pulling the wheels out of the slots
(FIG. 5.II). Insert the front wheels in the slot in the front axle until you hear the locking sound (FIG. 6). To remove the front
wheels, push the quick release button located below the footrest under each wheel (FIG. 7). The buggy has a system of
swivel front wheels with a possibility of locking for straight movement. To lock the wheel to move forward, slide the ring
located above the wheel (FIG 8).
NOTE! Before using the buggy, make sure that all the wheels are
properly installed.
IV. CANOPY INSTALLATION
When installing the canopy, slide the attachments into the guides on both sides of the frame until they lock (FIG. 9). Then
fasten the Velcro fasteners on both sides of the canopy (FIG. 10). A correctly mounted canopy is shown in FIG. 11. In order
to unfold another layer of the canopy, unfasten the zip on the canopy (FIG. 12).
V. ASSEMBLY/DISASSEMBLY OF THE SAFETY BAR
The safety bar must be inserted in appropriate holes on both sides of the frame, as shown in FIG. 13. To remove the bar,
press the buttons on both sides and remove the bar (FIG. 14).
VI. USE OF BRAKE
The buggy is equipped with a foot brake located on the rear axle. Press the lower part of the brake down; the brake is
activated when you hear the locking sound (FIG. 15). The brake is unlocked by pressing the upper part of the brake.
VII. BACKREST AND FOOTREST ADJUSTMENT
The seat is equipped with smooth backrest adjustment system, from a lying to a sitting position, using a clasp (FIG. 16.I).
The footrest has 4 positions. Press the buttons on both sides (FIG. 16.II) to change the footrest position.
VIII. SAFETY STRAPS
D. Safety bar
E. Visor
H. Cup holder
16