Descargar Imprimir esta página

Bosch 060160A101 Manual Original página 14

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 28
Tool Specifications
Laminate trimmer
Article number
Rated power input
No-load speed
Tool holder
Weight according to
EPTA-Procedure
01/2003
Protection class
Please observe the article number on the type plate of
your machine. The trade names of the individual ma-
chines may vary.
The values given are valid for nominal voltages [U] of
230/240 V. For lower voltages and models for specific
countries, these values can vary.
Noise/Vibration Information
Measured values determined according to
EN 60 745.
Typically the A-weighted noise levels of the ma-
chine are: sound pressure level 84 dB (A);
sound power level 95 dB (A).
Uncertainty K = 3 dB.
Wear hearing protection!
Overall vibrational values (vector sum of three
directions) determined according to EN 60745:
Vibrational emission value a
2
tainty K=1.5 m/s
.
The vibration emission level
WARNING
given in this information sheet
has been measured in accordance with a stand-
ardised test given in EN 60745 and may be
used to compare one tool with another.
The vibration emission level will vary because of
the ways in which a power tool can be used and
may increase above the level given in this infor-
mation sheet. This could lead to a significant un-
derestimate of exposure when the tool is used
regularly in such a way.
NOTE: To be accurate, an estimation of the
level of exposure to vibration experienced dur-
ing a given period of work should also take into
account the times when the tool is switched off
and when it is running but not actually doing the
job. This may significantly reduce the exposure
level over the total working period.
14 | English
GKF 600
Professional
3 601 F0A 1..
[W]
600
[rpm] 33 000
6 mm/
8 mm/
1
/
" (only UK)
4
[kg]
1.5
/ II
2
=4.5 m/s
, uncer-
h
Declaration of Conformity
We declare under our sole responsibility that the
product described under „Technical data" is in
conformity with the following standards or stand-
ardization documents: EN 60745 according to
the provisions of the directives 2004/108/EC,
98/37/EC (until 28 Dec 2009), 2006/42/EC (from
29 Dec 2009).
Technical documents at:
Robert Bosch GmbH, PT/ESC,
D-70745 Leinfelden-Echterdingen
Dr. Egbert Schneider
Senior Vice President
Engineering
03.12.2007, Robert Bosch GmbH, Power Tools Division
D-70745 Leinfelden-Echterdingen
Product Features
While reading the operating instructions, unfold
the graphics page for the machine and leave it
open.
The numbering of the product features refers to
the illustration of the machine on the graphics
page.
1 Motor unit
2 Routing base
3 Thumbwheel for depth-of-cut fine
adjustment
4 Router bit*
5 Collet chuck
6 Guide plate
7 Base plate
8 Scale for depth-of-cut adjustment
9 Spindle lock button
10 Clamping lever
11 On/Off switch
12 Open-end spanner
13 Collet
14 Guide bushing*
15 Rubber ring
16 Guide plate, round*
17 Fastening screw for base plate (4 x)
18 Centring pin*
19 Knurled screw for attachment of side stop
20 Parallel guide
Dr. Eckerhard Strötgen
Head of Product
Certification
2 609 140 541 • 22.1.08

Publicidad

loading

Este manual también es adecuado para:

Gkf 600 professional