Publicidad
Idiomas disponibles
Idiomas disponibles
first selected channel. You can press the Yellow button
and enter the number of the channel you want to select.
Then highlight OK and press OK to go to that channel.
You may need to set the LCN option to Off in order to
enable this feature.
Channel Move: Move a channel to the position of
another channel. Highlight the channel you want to
move and press OK to select. Then do the same for a
second channel. When the second channel is selected,
you can press the Blue button and the first selected
channel will be moved to the position of that channel.
You can press the Yellow button and enter the number
of the channel you want to select. Then highlight OK
and press OK to go to that channel. You may need to
set the LCN option to Off in order to enable this feature.
Channel Edit: Edit channels in the channel list. Edit
the name of the selected channel and display Network
Name, Channel Type and Frequency information
related to that channel if available. Depending on the
channel other options may also be editable. Press OK
or the Yellow button to edit the highlighted channel.
You can press the Blue button to delete the highlighted
channel.
Channel Delete: Highlight the desired channel/s on
the list and press OK or the Yellow button to select/
unselect. Then press the Blue button to delete the
selected channel/s.
Clear Channel List: Delete all channels stored in the
channel list. A dialogue will be displayed for confirma-
tion. Highlight OK and press OK button to proceed.
Highlight Cancel and press OK to cancel.
Input Source - Cable
Channel Scan: Start a scan for digital cable channels.
If available, operator options will be listed. Select the
desired one and press OK. Scan Mode, Frequency
and Network ID options may be available. The options
may vary depending on the operator and the Scan
Mode selections. Set the Scan Mode as Full if you
don't know how to set up other options. Highlight Scan
and press OK or the Right directional button to start
the scan. You can press the Back/Return button to
cancel the scan. The channels that have already been
found will be stored in the channel list.
Single RF Scan: Enter the Frequency value. Signal
Level and Signal Quality of the selected Frequency
will be shown. Highlight the Scan option and press OK
or the Right directional button to start scan. The found
channels will be stored in the channel list.
LCN: Set your preference for LCN. LCN is the Logical
Channel Number system that organises available
broadcasts in accordance with a recognisable channel
number sequence (if available).
Channel Scan Type: Set your scan type preference.
Channel Store Type: Set your store type preference.
Favourite Network Select: Select your favourite net-
work. This menu option will be active, if more than one
network is available. This option may not be available
depending on the selected country during the initial
setup process.
Channel Skip: Set channels to be skipped when
switching the channels via Programme +/- buttons
on the remote. Highlight the desired channel/s on the
list and press OK to select/unselect.
Channel Swap: Replace the positions of the two
selected channels in the channel list. Highlight the
desired channels on the list and press OK to select.
When the second channel is selected, the position of
this channel will be replaced with the position of the
first selected channel. You can press the Yellow button
and enter the number of the channel you want to select.
Then highlight OK and press OK to go to that channel.
You may need to set the LCN option to Off in order to
enable this feature.
Channel Move: Move a channel to the position of
another channel. Highlight the channel you want to
move and press OK to select. Then do the same for a
second channel. When the second channel is selected,
you can press the Blue button and the first selected
channel will be moved to the position of that channel.
You can press the Yellow button and enter the number
of the channel you want to select. Then highlight OK
and press OK to go to that channel. You may need to
set the LCN option to Off in order to enable this feature.
Channel Edit: Edit channels in the channel list. Edit
the name of the selected channel and display Network
Name, Channel Type, Frequency, Modulation and
Symbol Rate information related to that channel.
Depending on the channel other options may also be
editable. Press OK or the Yellow button to edit the
highlighted channel. You can press the Blue button
to delete the highlighted channel.
Channel Delete: Highlight the desired channel/s on
the list and press OK or the Yellow button to select/
unselect. Then press the Blue button to delete the
selected channel/s.
Clear Channel List: Delete all channels stored in the
channel list. A dialogue will be displayed for confirma-
tion. Highlight OK and press OK button to proceed.
Highlight Cancel and press OK to cancel.
Satellite Re-scan: Start a satellite scan beginning
with the antenna selection screen. When this scanning
option is preferred, some scanning configurations will
not be available and thus the preferences you made
during the initial setup process may not be changed.
For the General Satellite channel installation mode
SatcoDX Scan option may also be available here.
Copy the relevant sdx file into the root directory of an
USB storage device and connect it to your TV. Highlight
English - 16 -
Input Source - Satellite
Publicidad
