Bort BHK-185U Instrucciones De Servicio página 7

build-up of debris)
• Lower guard should be retracted manually only
for special cuts such as plunge cuts and compound
cuts; raise lower guard by retracting handle and as
soon as blade enters the material, the lower guard
must be released (for all other sawing, the lower guard
should operate automatically)
• Always observe that the lower guard is covering
the blade before placing saw down on bench or
fl oor (an unprotected, coasting blade will cause the
saw to walk backwards, cutting whatever is in its path;
be aware of the time it takes for the blade to stop after
switch is released)
• Avoid damage that can be caused by screws, nails
and other elements in your workpiece; remove them
before you start cutting
• When you put away the tool, switch off the motor and
ensure that all moving parts have come to a complete
standstill
• Use completely unrolled and safe extension cords
with a capacity of 16Amps (U.K. 13Amps)
• In case of jamming or electrical or mechanical
malfunction, immediately switch off the tool and
disconnect the plug
• The SBM Group can assure fl awless functioning of
the tool only when original accessories are used
• Use only accessories with an allowable speed
matching at least the highest no-load speed of the tool
• Never use the tool without the original protection
guard system
• This tool should not be used by people under the age
of 16 years
• The noise level when working can exceed 85 dB(A);
wear ear protection
• If the cord is damaged or cut through while working,
do not touch the cord, but immediately disconnect the
plug
• Never use tool when cord is damaged; have it
replaced by a qualifi ed person
• Always check that the supply voltage is the same as
the voltage indicated on the nameplate of the tool (tools
with a rating of 230V or 240V can also be connected to
a 220V supply)
• This tool is not suitable for wet cutting
• After switching off your circular saw, never stop the
rotation of the saw blade by a lateral force applied
against it
• Never use circular saw blades made of high speed
steel (HSS)
• Never use grinding/cutting discs with this tool
• Do not work materials containing asbestos
(asbestos is considered carcinogenic)
• Take protective measures when during work
dust can develop that is harmful to one's health,
combustible or explosive (some dusts are considered
carcinogenic); wear a dust mask and work with dust/
chip extraction when connectable
• Do not attempt to cut extremely small workpieces
• Remove all obstacles on top of as well as underneath
the cutting path before you start cutting
• Do not work overhead with the tool
• Only use a saw table provided with a switch that
prevents restarting of the motor after interruption of
voltage
• Only use a saw table provided with a kerf guide
• Always disconnect plug from power source
before making any adjustment or changing any
accessory
WHEN CONNECTING NEW 3-PIN PLUG (U.K.
ONLY):
• Do not connect the blue (= neutral) or brown (= live)
wire in the cord of this tool to the earth terminal of the
plug
• If for any reason the old plug is cut off the cord
of this tool, it must be disposed of safely and not left
unattended
Your machine is double insulated in accord-
ance with EN 50144; therefore no earthwire
is required.
MAINTENANCE
Make sure that the machine is not live when
carrying out maintenance work on the motor.
Regularly clean the machine housing with a soft cloth,
preferably after each use. Keep the ventilation slots free
from dust and dirt.If the dirt does not come off use a soft
cloth moistened with soapy water. Never use solvents
such as petrol, alcohol, ammonia water, etc. These sol-
vents may damage the plastic parts.
The machine requires no additional lubrication.
Should a fault occur, e.g. after wear of a part, please
contact your local SBM Group dealer.
ENVIRONMENT
In order to prevent the machine from damage during
transport, it is delivered in a sturdy packaging. Most of
the packaging materials can be recycled. Take these
materials to the appropriate recycling locations. Take
your unwanted machines to your local SBM Group
dealer. Here they will be disposed of in an environmen-
tally safe way.
7