Publicidad
Idiomas disponibles
Idiomas disponibles
Listening through a Receiver
You can listen to sound through a receiver instead of the TV speaker.
1
Press the MENU button to display the menu.
Press the ▲ or ▼ button to select Input, then press the ENTER button.
Press the ▲ or ▼ button to select Anynet + (HDMI-CEC), then press the ENTER
button.
Press the ▲ or ▼ button to select Receiver, then press the ENTER button.
4
Press the ◄ or ► button to select to On, then press the ENTER button.
Now you can listen to sound through the receiver.
5
Press the EXIT button to exit.
➢
When the receiver is set to On, you can listen to the TV sound through the 2-
channel receiver.
➢
If the receiver is exclusively for a home theater only (supporting audio only), it may
not appear in the device list.
➢
In case of a content with copyright problems, listening through the receiver may not properly operate.
➢
When listening through the receiver, there are restrictions for using the PIP and audio-related menu.
Check Points before Requesting Service
Symptom
Anynet + does not work.
I want to start Anynet + .
I want to exit Anynet + .
The message Connecting to
Anynet + device... appears
on the screen.
The Anynet + device does
not play.
The connected device is not
displayed.
The TV programme cannot
be recorded.
BN68-01528A-Eng.indb 35
Solution
Check if the device is an Anynet + device. The Anynet + system
■
supports Anynet + devices only.
■
Connect only one receiver.
Check if the Anynet + device power cord is properly connected.
■
Check the Anynet + device's Video/Audio/HDMI cable connections.
■
Check whether Anynet + (HDMI-CEC) is set to On in the Anynet +
■
setup menu.
■
Check whether the TV remote control is in TV mode.
Check whether it is Anynet + exclusive remote control.
■
Anynet + doesn't work at a certain condition. (Searching channels)
■
■
When connecting or removing the HDMI cable, please make sure
to search devices again or restart your TV.
Check if the Anynet + Function of Anynet + device is set on.
■
Check if the Anynet + device is properly connected to the TV and
■
check if the Anynet + (HDMI-CEC) is set to On in the Anynet +
Setup menu.
■
Press the TV button on the TV remote control to switch to TV.
Then press the TOOLS button to show the Anynet + menu and
select a menu you want.
Select View TV in Anynet + menu.
■
■
Press the SOURCE button on the TV remote control and select a
device other than Anynet + devices.
■
Press any of P, CH LIST, and PRE-CH to change to the
TV mode. (Note that the channel button operates only when a
tuner-embedded Anynet + device is not connected.)
■
You cannot use the remote control when you are configuring
Anynet + or switching to a view mode.
Use the remote control when the Anynet + setting or switching to
■
view mode is complete.
■
You cannot use the play function when Plug & Play is in progress.
Check whether or not the device supports Anynet + functions.
■
■
Check whether or not the HDMI cable is properly connected.
Check whether Anynet + (HDMI-CEC) is set to On in the Anynet +
■
setup menu.
Search Anynet + devices again.
■
You can connect an Anynet + device using the HDMI cable only.
■
Some HDMI cables may not support Anynet + functions.
■
Check whether the antenna jack on the recording device is
properly connected.
English - 5
TV
P 1
View TV
Select Device
Record
Menu on Device
Device Operation
Receiver
:On
Setup
Move
Enter
Exit
2008-04-18 오후 1:44
Publicidad
