Fitwood TAIMI MINI WALL BARS Manual Del Propietário página 4

Foreword
EN
Thank you very much for choosing the FitWood TAIMI MINI wall bars. Please read this guide
thoroughly before assembly and follow each process step by step so you can enjoy the product
safely.
Please keep this user guide for future reference.
If you need assistance assembling the product, you may contact us directly.
FitWood Ltd
Hautalankatu 20
33560 Tampere
Finland
info@fitwood.com
Disclaimer
Read all instructions before using the product and follow assembly instructions accordingly.
FitWood cannot be held responsible in any way for any loss or injury, howsoever caused, as a result
of neglecting the instructions, misusing the product or misunderstanding the information contained
in this document or on our website.
Warranty applies only for the defects in the product and in case of complaint only the product
or its component will be replaced. The warranty does not cover damage due to negligent use of
the product, natural wearing of the product material or features, or breakage that is caused by an
unfavorable environment. FitWood Ltd will not be liable for any injury or death resulting from
improper assembly, maintenance, or use of this product. FitWood's warranty is limited only to
repairing or replacing a faulty product.
Recommended tools
• Drill and Torx TX30 bit
• Stud finder
• Tape measure
• Block of wood
Varmista, että pakkauksesta löytyy seuraavat osat
• Frame pieces, 2 pcs
• Rungs, 10 pcs
• Support beams, 2 pcs
6
• Level
• Pencil
• Rubber mallet
• Screws 6 x 80 mm TX25, 16 pcs
(For attaching support beams and rungs.)
• Round cover stickers, 8 pcs
• Screws 6 x 80 mm TX25, 4 pcs
(For attaching the support beams to a plasterboard wall
with wooden studs. Suitability for intended use must be
confirmed by a qualified professional.)
• Nylon plugs, 4 pcs
(To fasten support beams to a concrete wall together
with 4pcs of 6 x 80 mm TX25 screws. Suitability
for intended use must be confirmed by a qualified
professional.)
Attention
FitWood recommends that a qualified professional installs your TAIMI MINI wall bars to ensure proper
and safe connection to studs or other type of wall structure. The package includes fastening screws
which, for example, can be used for fastening TAIMI MINI wall bars to:
• A plasterboard wall with wooden studs
• A concrete wall
Please note that FitWood cannot specifically know what kind of wall the end user has (e.g. wall
material and wall thickness). Therefore, FitWood only provides sample screws. If necessary, purchase
the fastening materials that suit your needs according to the qualified professional's instructions.
FitWood is not responsible for supplying the correct type of fastening supplies with the product.
When installing the product in a public space or structure with metal supports, a qualified
professional must define which materials and fasteners are considered safe for attaching the TAIMI
MINI wall bars to the wall. The product package does not contain supplies for attaching TAIMI MINI
wall bars to metal supports.
FitWood is not responsible for damages to the product or to the surrounding material, such as the
wall, which have occurred due to improper or incorrect installation of FitWood TAIMI MINI wall bars.
FitWood is also not responsible for any personal injuries or death caused by improper or incorrect
installation or use of the FitWood TAIMI MINI wall bars.
Installing the support beams on the wall
Please note! The support beams are 68 cm wide and can be mounted to wooden wall studs that
are 60 cm apart or at any other undefined distance from each other, if the distance is less than 60
cm. Before installation, hire a qualified professional to verify, that the screws included in the product
package are suitable for the particular wall material. The nylon plugs can be used to mount the wall
bars to a concrete wall, if a qualified professional confirms that they are suitable for the wall material
in question.
Step 1 (mounting to plasterboard wall)
Use the stud finder to locate the wooden studs in the wall, so you can mount the TAIMI MINI wall
bars to them. Once you've located the studs, measure the distance between them.
Step 2 (mounting to plasterboard wall)
From the center of the support beam, measure half the distance between the studs. For example,
if the distance between the studs is 60 cm, measure 30 cm from the center of the support beam
towards the outer edges. Remember to also consider the width of the studs when you mark the
positions of the holes on the support beam.
Step 3
Mark the positions of the mounting holes on the wall bars' support beams with dots. Remember
to also mark the desired position of the wall bars on the wall. Hire a qualified professional to verify
that you have the correct size screws and proper mounting materials at your disposal to attach the
support beams to the studs or other wall material securely.
Step 4
Pre-drill the holes you marked on the support beams for fastening. We recommend that you hire
a qualified professional to verify that the size of the pilot holes for the selected fastening screws
is correct. Do not drill holes to the glue joint of the support beam, because that might cause the
support beam to crack. Additionally, we recommend avoiding the use of countersunk screws,
because those might also cause the support beam to crack.
EN
7