LEGRAND Wattstopper WRC-TX-LM Instrucciones De Instalación

No: 24984 – 08/18 rev. 1
Catalog Number • Numéro de Catalogue • Número de Catálogo: WRC-TX-LM
Country of Origin: Made in China • Pays d'origine: Fabriqué en Chine • País de origen: Hecho en China
READ & SAVE THESE INSTRUCTIONS! CAUTION:
• To prevent severe shock or electrocution, always
turn power OFF at the service panel before
working with wiring.
• Use this device with copper or copper-clad wire.
Do not use with aluminum wire.
• Must be installed in accordance with National
and Local electrical codes.
WARNING: IMPROPER WIRING OF ANY
ELECTRICAL DEVICE CAN CAUSE SERIOUS
INJURY OR DEATH. THESE WIRING DEVICES
SHOULD BE INSTALLED BY AN ELECTRICIAN OR
OTHER QUALIFIED PERSON.
The Radio Frequency (RF) Plug Load Controller expands the energy savings obtained from traditional occupancy sensing to
encompass AC receptacles as well as built-in lighting. We accomplish this by providing an RF transmitter (WRC-TX-LM) that connects
to your new or existing occupancy sensor, and a switched AC receptacle (WRC-15-x, WRC-20-x) that contains a built-in RF receiver.
The RF Signal Pack (transmitter) connects to any DLM Room network. When the RF Signal Pack receives an "vacancy" signal from the
sensor, it transmits a message commanding the receptacle to turn off. Similarly when the office becomes occupied, the sensor sends
a signal to the RF transmitter and the receptacles turn on. Each RF Signal Pack can control up to 16 RF receptacles. A switched feed
through allows for control of downstream receptacles from a single RF receptacle. Recommended communication range between RF
Signal Pack and RF Receptacle is 30 feet. Greater distances can be achieved in ideal environments.
1. After removing power as described above, use strip gauge on back of outlet to strip all wires to desired length (if not already
stripped).
2. Attach wires according to the diagram below. Be sure the wires are fastened securely either by the terminal screws or through the
back-wire holes in the back of the outlet.
WARNING: LOOSELY FASTENED WIRES MAY RESULT IN OUTLET FAILURE AND/OR FIRE HAZARD.
If using terminal screws: Terminal screws accept up to #12 AWG wire. Wrap each stripped wire 3/4 turn clockwise under heads
of screws without overlapping and tighten securely.
If using back-wire method: Back-wire accepts up to a #12 AWG wire. Insert stripped wire between external pressure plate clamp
and terminal. Tighten securely.
3. Mount outlet in box using mounting screws supplied. Attach wall plate. Restore power only when finished wiring the entire circuit.
LIRE ET CONSERVER CES INSTRUCTIONS.
ATTENTION
• Pour éviter tout choc électrique ou une électrocution,
coupez toujours l'électricité au niveau du panneau
d'alimentation avant de commencer à câbler.
• Utilisez ce dispositif avec des fils en cuivre ou
cuivrés. Ne l'utilisez pas avec des fils en aluminium.
• Doit être installé conformément aux codes locaux et
nationaux de l'électricité.
AVERTISSEMENT: LE CÂBLAGE INCORRECT DE
TOUT DISPOSITIF ÉLECTRIQUE PEUT CAUSER
DES BLESSURES GRAVES, VOIRE LA MORT.
CES DISPOSITIFS DE CÂBLAGE DOIVENT ÉTRE
INSTALLÉS PAR UN ÉLECTRICIEN OU UNE
PERSONNE QUALIFIÉE.
RECEPTACLE INSTALLATION INSTRUCTIONS
Green or Bare Wire
Green Screw
Brass Screw
Brass Screw
15A or 20A
Controlled
125V
250V
125V
Wattstopper
Radio Frequency (RF) Plug Load Controller For DLM Systems
Commande de charge de prise à fréquence radio (RF) pour systèmes DLM
Controlador para cargas comunes con alimentación CA de radiofrecuencia (RF)
para sistemas DLM
Installation Instructions • Instructions d'Installation • Instrucciones de Instalación
DESCRIPTION
White Screw
Brass Screw
Not required if both
faces are controlled
or
Line
Neutral
Figure 1
®
LEA Y GUARDE ESTAS INSTRUCCIONES.
PRECAUCIÓN:
• Para evitar serios electrochoques o electrocución,
siempre APAGUE el suministro eléctrico en el
panel de servicio antes de trabajar con los cables.
• Utilice este dispositivo con alambres de cobre o
revestidos de cobre. No usar con cables de aluminio.
• Se debe instalar de acuerdo con los códigos
eléctricos nacionales y locales.
ADVERTENCIA: EL CABLEADO INCORRECTO DE UN
DISPOSITIVO ELÉCTRICO PUEDE CAUSAR LESIONES
GRAVES O AÚN LA MUERTE. UN ELECTRICISTA U
OTRA PERSONA COMPETENTE DEBE INSTALAR
ESTOS DISPOSITIVOS DE CABLEADO.
Green Screw
White Screw
15A or 20A