Magicvac P0606ED Instrucciones De Uso página 14

- Press down on the rounded recessed area of the manual valve (5) to release the lid.
- Lift the lid and turn it in the open position.
- Check the quality of the seal obtained, which should appear as a regular, wrinkle-free crosswise strip with no
internal ridges in the bag (fig. B).
4 Vacuum packing with bags cut from a roll or pre-cut bags
- Lift the lid (4) and turn it in the open position.
- Place food in the bag without creasing it excessively or stretching surfaces. Eliminate any liquids or food
residues from the area inside the bag that will be sealed.
- Place the bag and its contents in front of the appliance and place the open end inside the vacuum chamber
(11) with the smooth side facing down (fig. D1).
WARNING: have the end of the bag protrude inside the VACUUM CHAMBER. See the yellow dotted line (fig. D1)
- Close the cover (4), put pressure on the two opposite ends and hook in by pressing the LOCK (7) buttons,
see (fig. C2). The unit will automatically start the packing cycle and will stop at the end of the cycle, when
the SEAL red light (2) goes off.
- Press down on the rounded recessed area of the manual valve (5) to release the lid.
- Lift the lid and turn it in the open position.
- Check the quality of the seal obtained, which should appear as a regular, wrinkle-free crosswise strip with no
internal ridges in the bag. (fig. B)
- You can interrupt a packaging cycle already in progress at any time by means of the manual valve (5), keep-
ing it pressed until the machine turns off.
5 How to use the MAN SEAL button (3)
Pressing this button causes the SEAL light (2) to go on and the sealing process starts immediately. This allows
you to prevent delicate, fragile foods from being crushed (e.g. biscuits, etc.).
6 Vacuum packing in MAGIC VAC ® Executive containers or in containers sealed with MAGIC VAC ®
Universal Caps
MAGIC VAC ® Executive containers and the MAGIC VAC ® Universal Caps with star-shaped knob (see fig. E1)
make vacuum packing easier, because the connection hose can be directly introduced into the knob central
hole (see fig. E2).
MAGIC VAC ® Universal Caps, available in two diameters (100 mm and 125 mm), are to be used on jars for pre-
serving food and bowls and receptacles made of tempered glass. The Universal Caps work just like the Caps
for MAGIC VAC ® Executive containers.
WARNING: When using Universal Caps do not use plastic or glass containers that are not suitable since they
could implode under the vacuum pressure of the appliance and cause injury.
- Fill the container leaving at least 3 cm of room between the contents and upper rim. Place the lid on the
container and turn the knob to the "VACUUM" position (fig. E1).
- Connect the container lid knob to the appliance air inlet (6) by means of the connection hose (fig. E2).
- Lock the lid (4) by pushing the LOCK buttons (7); the machine will carry out a vacuum packing cycle and turn
off automatically on its completion.
- Remove the hose from the container lid knob.
- Turn the knob to the "CLOSED" position.
- To open the containers turn the knob to the "OPEN" position, you should hear a hissing of air as it enters the
container. This sound guarantees that the contents have been packed in a vacuum.
7 Vacuum packing in MAGIC VAC ® Family containers
Multipurpose containers ideal for storage of frequently used products such as dry and fragile foods; powder
foodstuffs; fresh, pureed or strained fruit and vegetables. Their transparency and design makes them attractive
to display on kitchen shelves while ensuring that their contents are clearly visible.
- Fill the container leaving at least 3 cm of room between the contents and upper rim and position the cap on
the container.
- Connect the container lid to the air inlet (6) of the appliance (fig. F) by means of the connection hose (15).
- Lock the lid (4) by pushing the LOCK buttons (7); the machine will carry out a vacuum packing cycle and turn
off automatically on its completion.
- Remove the hose from the container lid.
- To open the container, move the flaps of the Valve (16) (fig. F).
8 Vacuum packing in glass jars sealed with metal caps (Leifheit type)
Use the cap attachment to pack foods in large-mouthed glass jars with a metal cap.
- Fill the container leaving at least 3 cm of room between the contents and upper rim.
- Connect the cap attachment (17) to the air inlet (6) of the appliance by means of the connection hose (15).
Place the cap attachment directly on the jar with the metal cap only (18) and press down, making sure it fits
correctly. (fig. G1)
- Lock the lid (4) by pushing the LOCK buttons (7); the machine will carry out a vacuum packing cycle and turn
off automatically on its completion. Make sure that the cap attachment holds firmly by keeping it pressed
with your hand.
- Disconnect the hose from the cap attachment. Remove the cap attachment from the jar.
- Apply the ring (19) supplied with the jar and screw it down all the way (fig. G1).
- To open a glass jar vacuum-sealed with a metal cap, use the cap opener provided (the side with writing
should be turned up). Position the cap opener as shown in (fig. G2) and gently pry open the cap until the
vacuum is released. Remove the metal cap. This accessory allows you to reuse the cap.
9 Vacuum packing with MAGIC VAC ® bottle caps
The MAGIC VAC ® Bottle Cap may be used to seal partly filled bottles of wine or non-fizzy beverages. Using the
13