System Parameters; Troubleshooting - Boss Vocal PERFORMER VE-20 Manual De Instrucciones

CONTROL PEDAL
Parameter Explanation
Type DBL/HRM
DELAY
PITCH
Switches each effect on/off (p. 14).
TONE/SFX
REVERB
DYNAMICS
CUSTOM Turns the specified effect on/off (p. 14).
MASTER
Parameter Explanation
Level Specifies the volume of the sound.
NoiseThres Adjust this according to the noise level.
Set this to a larger value if the noise level is high, or
to a lower value if the noise level is low.
Key Specifies the key of the song you're singing (p. 11).

System parameters

These parameters are applied to the entire VE-20.
SETUP
Parameter Explanation
MicSens Adjusts the input sensitivity.
PhantomPow- Turns on/off the supply of phantom
On, Off
er power to the INPUT jack.
Output Mono output from OUTPUT connec-
Mono
tors L (MONO) and R.
Stereo output from the OUTPUT con-
Stereo
nectors.
Mono output from OUTPUT connec-
tor L (MONO) and Dry sound from
connector R.
Mono/Dry
* This setting also applies to the L and
LowCut Cuts unwanted low-frequency con-
On, Off
tent.
LoopType Select this if you want to use the
Perform Phrase Loop function to overdub (p.
13).
Select this if you want to perform a
Check
sound check (p. 15).
Contrast Adjusts the display contrast (legibility).
FACTORY RESET
Parameter Explanation
ALL All settings will be initialized.
SOUND All user sound settings will be initialized.
SETUP Setup parameter settings will be initialized.
R signals of the PHONES/LINE jack.

Troubleshooting

Power doesn't come on
Have the batteries run down?
→ Replace them with new batteries (p. 3).
* The batteries included with the VE-20 are meant only to confirm that
the unit is functional at the factory.
Is the specified AC adaptor (PSA series; optional)
connected correctly?
→ Check the connections again (p. 7).
Never use any AC adaptor other than the adaptor
specified.
Could the POWER switch be OFF?
→ Turn the POWER switch ON (p. 4).
No sound/volume is low
Is the other equipment connected correctly?
→ Check the connections again (p. 7).
Could the volume or input gain of the connected
mixer or recorder be lowered?
→ Check the settings of the connected device.
Could the Phantom Power parameter be set to Off?
→ If you're using a condenser mic that requires phantom
power, set the Phantom Power parameter to the On (p. 16).
Could the MicSens or Volume settings be too low?
→ Adjust these to appropriate values (p. 4).
Have the batteries run down?
→ Replace them with new batteries (p. 3).
* The batteries included with the VE-20 are meant only to confirm that
the unit is functional at the factory.
The POWER indicator has gone dim
Is the specified adaptor (PSA series; optional)
properly connected?
→ Check the connection once more (p. 7).
* Never use any AC adaptor other than one specified for use with the
VE-20.
Have the batteries run down?
→ Replace them with new batteries (p. 3).
* When the indicator goes dim or no longer lights while the effect is on,
it means that the batteries must be replaced.
* The batteries included with the VE-20 are meant only to confirm that
the unit is functional at the factory.
Sound is distorted
Is the MicSens setting appropriate?
→ Adjust the setting appropriately (p. 4).
Is the output from another effects processor
connected to the INPUT jack?
→ Connect your mic directly to the INPUT jack.
Can't store the recorded phrase
→ It is not possible to store a recorded phrase in the VE-20.
Can't overdub using Phrase Loop
Could the Phrase Loop parameter be set to Check?
→ Overdubbing is not possible if this is set to Check.
If you want to overdub, set the Phrase Loop parameter
to Perform (p. 15).
Appendix
19