Grohe ESSENCE E 36 445 Manual Del Usuario página 5

Störung / Ursache / Abhilfe
Störung Ursache
Wasser fließt nicht • Sieb vor Magnetventil verstopft
• Magnetventil defekt
• Steckverbinder ohne Kontakt
• Keine Spannung
- Batterie leer
(Kontrollleuchte signalisiert Dauerleuchten)
- Netzteil defekt
Wasser fließt • Erfassungsbereich der Sensorik für örtliche
ungewollt Gegebenheiten zu groß eingestellt
• Automatische Spülung aktiv
• Magnetventil defekt
Wassermenge zu • Mousseur verschmutzt
gering
• Sieb vor Magnetventil verschmutzt
• Siebe in Anschlussschläuchen verschmutzt
GB
Safety notes
Prevent danger resulting from damaged voltage
supply cables.
If damaged, the voltage supply cable must be
replaced by the manufacturer or his customer service
department or an equally qualified person.
• Installation is only possible in frost-free rooms.
• The plug-in voltage supply is only suitable for indoor use.
• The plug-in connectors must not be directly or indirectly
sprayed with water when cleaning.
• The voltage supply must be separately switchable.
• Use only genuine replacement parts and accessories.
The use of other parts will result in voiding of the warranty
and the CE identification, and could lead to injuries.
Technical data
Fitting with switched-mode power supply:
• Voltage supply: 100-240 V AC 50-60 Hz/6.75 V DC
• Power consumption:
Fitting with battery:
• Voltage supply:
• Automatic safety shut-off:
(6 - 420 s adjustable)
• Run-on time: (0 - 19 s adjustable)
• Reception range according to
Kodak Gray Card, grey side,
8x10", landscape:
12 cm (7 - 20 cm adjustable)
20 cm (7 - 22 cm adjustable)
• Type of fitting protection:
Thermal disinfection possible.
Electrical test data
• Software class
• Contamination class
• Rated surge voltage
• Temperature of ball impact test
2.4 W
6V lithium battery type CR-P2
60 s
1 s
20 cm 12 cm
IP 59K
A
2
2500 V
100 °C
Abhilfe
- Sieb reinigen
- Magnetventil austauschen
- Steckverbinder prüfen
- Batterie austauschen
- Netzteil austauschen
- Reichweite mit Fernbedienung (Sonderzubehör,
Bestell-Nr.: 36 407) / App reduzieren
- 1 - 10 Minuten warten
- Magnetventil austauschen
- Mousseur reinigen oder austauschen
- Sieb reinigen
- Siebe reinigen oder austauschen
The test for electromagnetic compatibility (interference emission
test) was performed at the rated voltage and rated current.
If static pressures exceed 0.5 MPa, a pressure-reducing valve
must be installed.
Avoid major pressure differences between hot and cold water
supply!
Approval and conformity
This product conforms to the requirements of the
relevant EU guidelines.
The conformity declarations can be obtained from the following
address:
GROHE Deutschland Vertriebs GmbH
Zur Porta 9
D-32457 Porta Westfalica
Installation
, see fold-out page II.
Flush pipes thoroughly before and after
installation (observe EN 806)!
Open hot and cold water supply and check that
connections are watertight.
Setting temperature limiter,
see fold-out page II.
Operation and settings,
see technical product information, 99.0438.xxx.
Activating setting mode
Disconnect the power supply to the electronics and reconnect
after 10 s.
The indicator lamp in the sensor system illuminates in setting
mode when the detection zone of the fitting is reached by an
approaching user.
Setting mode is automatically terminated after 3 minutes.
2