Publicidad
Idiomas disponibles
Idiomas disponibles
6. Press the spool down GENTLY and rotate it until you
feel it is fixed in place and then push it to adjust it.
(When in place, the spool will rotate freely a few
degrees to the left and to the right). Be careful to keep
the line from getting stuck under the spool.
7. Replace the spool cover as shown in Fig. L, by
pushing and pressing on the reel cover.
Note: Make sure the cover is in the correct position,
you must hear two clicks to ensure that the two tabs
are correctly placed. Turn on the tool. In a few
seconds or less, you'll hear the nylon line cutting
automatically to the proper length.
MAINTENANCE
Maintenance and storage
a. Always unplug the machine from the electric power
supply (i.e. remove from the power outlet) before
cleaning or performing maintenance.
b. Use only parts and accessories recommended by the
manufacturer.
c. Inspect and maintain the machine regularly. The
machine must only be repaired by authorized
personnel.
d. When the machine is not in use, store it in a place
away from the reach of children.
Warning! To avoid serious injury, turn off and unplug
the tool before performing any
1. Keep the air intake slots clear (Fig. M) to prevent
overheating.
2. The cutting line can dry out over time. To keep the line
in optimum conditions, store the pre-coiled
replacement spools or the line in a sealed plastic bag
with a tablespoon of water.
3. Plastic parts can be cleaned using mild soap and a
damp cloth.
4. The line cutter on the end of the guard can become
dull over time. We recommend periodical maintenance
of the blade's edge with a file.
Important! To assure product SAFETY and RELIABILITY,
repairs, maintenance and adjustment (other than those
listed in this manual) should be performed by authorized
service centers or other qualified service personnel,
always using identical replacement parts.
ACCESSORIES
Use the BLACK & DECKER model DF-080 replacement
spool. Replace the nylon line (package or pre-coiled
replacement spool) as shown in this manual.
f Use only 2mm (0.08") diameter monofilament
lines. Do not use serrated or heavier gauge lines
because they could overload the motor and cause
overheating. The unit only works properly with 2mm
(0.08") diameter monofilament nylon line. You can get
maintenance.
this line through your local dealer or authorized
service center.
Warning! The use of accessories not recommended by
BLACK & DECKER for this tool can be dangerous.
PROTECTING THE ENVIRONMENT
Separate collection. This product must not be
disposed of with normal household waste.
Should you find one day that your
BLACK+DECKER product needs replacement, or
if it is of no further use to you, do not dispose of it
with household waste. Make this product available
for separate collection.
Separate collection of used products and packaging
allows materials to be recycled and used again.
Re-use of recycled materials helps prevent
environmental pollution and reduces the demand
for raw materials. Local regulations may provide for
separate collection of electrical products from the
household, at municipal waste sites or by the
retailer when you purchase a new product.
SERVICE INFORMATION
BLACK+DECKER offers a full network of company-owned
and authorized service locations. All BLACK+DECKER
Service Centers are staffed with trained personnel to
provide customers with efficient and reliable power tool
service. For more information about our authorized service
centers and if you need technical advice, repair, or genuine
factory replacement parts, contact the BLACK+DECKER
location nearest you, or visit us at www.BlackandDecker-
la.com
SPECIFICATIONS
Power
Voltage
AR, B2C
B3
B2
BR
No load speed
Cutting diameter
Feed type
Weight
Replacement spool
Line size
ENGLISH • 27
GH1000
900W
220V ~ 50Hz
120V ~ 60Hz
220V ~ 60Hz
127V ~ 60Hz
7200/min (rpm)
35cm (14")
Automatic
3,1kg (6,9lb)
DF-080
2mm (0,080")
Publicidad
