Descargar Imprimir esta página

Ryobi RAG1010-125 Traducción De Las Instrucciones Originales página 4

Ocultar thumbs Ver también para RAG1010-125:

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 17
operating procedures or conditions and can be avoided by
a) Maintain a firm grip on the power tool and
position your body and arm to allow you to
resist kickback forces. Always use auxiliary
handle, if provided, for maximum control
over kickback or torque reaction during start-
up. The operator can control torque reactions or
b) Never place your hand near the rotating
accessory.
hand.
c) Do not position your body in the area where
power tool will move if kickback occurs.
to the wheel's movement at the point of snagging.
d) Use special care when working corners, sharp
edges, etc. Avoid bouncing and snagging the
accessory. Corners, sharp edges or bouncing
have a tendency to snag the rotating accessory
e) Do not attach a saw chain woodcarving blade
or toothed saw blade. Such blades create
ADDITIONAL SAFETY INSTRUCTIONS FOR GRINDING
AND CUTTING-OFF OPERATIONS
cutting-off operations:
a) Use only wheel types that are recommended
for your power tool and the specific guard
designed for the selected wheel. Wheels for
which the power tool was not designed cannot be
adequately guarded and are unsafe.
b) The grinding surface of centre depressed
wheels must be mounted below the plane of
the guard lip. An improperly mounted wheel that
be adequately protected.
c) The guard must be securely attached to the
power tool and positioned for maximum safety,
so the least amount of wheel is exposed
towards the operator. The guard helps to protect
could ignite clothing.
d) Wheels must be used only for recommended
applications. For example: Do not grind with
the side of cut-off wheel. Abrasive cut-off wheels
are intended for peripheral grinding, side forces
applied to these wheels may cause them to shatter.
e) Always use undamaged wheel flanges that are
of correct size and shape for your selected
wheel. Proper wheel flanges support the wheel,
Flanges for cut-off wheels may be different from
grinding wheel flanges.
f) Do not use worn down wheels from larger
power tools. Wheel intended for larger power tool
is not suitable for the higher speed of a smaller tool
and may burst.
ADDITIONAL SAFETY WARNINGS SPECIFIC FOR
ABRASIVE CUTTING-OFF OPERATIONS
a) Do not "jam" the cut-off wheel or apply
excessive pressure. Do not attempt to make an
2
| English
excessive depth of cut. Overstressing the wheel
increases the loading and susceptibility to twisting
or binding of the wheel in the cut and the possibility
b) Do not position your body in line with and
behind the rotating wheel. When the wheel,
at the point of operation, is moving away from
spinning wheel and the power tool directly at you.
c) When wheel is binding or when interrupting a
cut for any reason, switch off the power tool
and hold the power tool motionless until the
wheel comes to a complete stop. Never attempt
to remove the cut-off wheel from the cut while
the wheel is in motion otherwise kickback may
occur.
eliminate the cause of wheel binding.
d) Do not restart the cutting operation in the
workpiece. Let the wheel reach full speed and
carefully re-enter the cut. The wheel may bind,
e) Support panels or any oversized workpiece
to minimize the risk of wheel pinching and
kickback.
their own weight. Supports must be placed under
f) Use extra caution when making a "pocket
cut" into existing walls or other blind areas.
The protruding wheel may cut gas or water pipes,
ANGLE GRINDER SAFETY PRECAUTIONS
a)
wheel is equal to or greater than the rated speed
of the product.
b) Ensure that the dimensions of the grinding wheel
are compatible with the product and that the wheel
fits the spindle.
c) Grinding wheels must be stored in a dry place.
d)
e) Grinding wheels must not be used for any operation
other than grinding.
f) Grinding wheels must be stored and handled
with care in accordance with the manufacturer's
instruction.
g) Inspect the grinding wheel before use to ensure
can cause the wheels to shatter, resulting in
h) Ensure that the wheel is fitted in accordance with
this manual.
i)
Ensure that the grinding wheel is correctly mounted
and tightened before use and run the product at
no-load speed for 30 seconds in a safe position.
Stop immediately if there is considerable vibration
or if other defects are detected. If this condition
Do not use separate reducing bushings or adapters
to adapt large hole grinding wheels.
l)
Use only grinding wheels approved by RYOBI.
m)

Publicidad

loading

Este manual también es adecuado para:

Rag950-125