Publicidad
OBJ_BUCH-3138-001.book Page 11 Monday, July 10, 2017 12:56 PM
Technical Data
Cordless Sheet Metal Shear
Article number
Rated voltage
Stroke rate at no load n
0
Max. steel sheet cutting capacity
Smallest curve radius
Weight according to
EPTA-Procedure 01:2014
Permitted ambient temperature
– during charging
2)
– during operation
and during
storage
Recommended batteries
Recommended chargers
2
1) to 400 N/mm
with reference to steel sheet
2) limited performance at temperatures <0 °C
Noise/Vibration Information
Sound emission values determined according to
EN 60745-2-8.
Typically the A-weighted sound pressure level of the product
is 70 dB(A). Uncertainty K=3 dB.
The noise level when working can exceed 80 dB(A).
Wear hearing protection!
Vibration total values a
(triax vector sum) and uncertainty K
h
determined according to EN 60745-2-8: a
2
K=1.5 m/s
.
The vibration level given in this information sheet has been
measured in accordance with a standardised test given in
EN 60745 and may be used to compare one tool with anoth-
er. It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main ap-
plications of the tool. However if the tool is used for different
applications, with different accessories or insertion tools or is
poorly maintained, the vibration emission may differ. This
may significantly increase the exposure level over the total
working period.
An estimation of the level of exposure to vibration should also
take into account the times when the tool is switched off or
when it is running but not actually doing the job. This may sig-
nificantly reduce the exposure level over the total working
period.
Identify additional safety measures to protect the operator
from the effects of vibration such as: maintain the tool and the
accessories, keep the hands warm, organisation of work
patterns.
Bosch Power Tools
Assembly
GSC 18V-16
Battery Charging
3 601 J26 2..
Use only the chargers listed in the technical data. Only
V=
18
-1
min
3400
1)
Note: The battery supplied is partially charged. To ensure full
mm
1.6
capacity of the battery, completely charge the battery in the
mm
15
battery charger before using your power tool for the first time.
The lithium-ion battery can be charged at any time without
kg
2.3 (5.0 Ah)
reducing its service life. Interrupting the charging procedure
does not damage the battery.
°C
0...+45
The lithium-ion battery is protected against deep discharging
by the "Electronic Cell Protection (ECP)". When the battery is
°C
–20...+50
empty, the machine is switched off by means of a protective
GBA 18V...
circuit: The inserted tool no longer rotates.
GBA 18V... W
Do not continue to press the On/Off switch after the
GAL 18...
GAL 18... W
Removing the battery
The battery 1 is equipped with two locking levels that should
prevent the battery from falling out when pushing the battery
unlocking button 2 unintentionally. As long as the battery is
inserted in the power tool, it is held in position by means of a
spring.
2
=9.6 m/s
,
h
To remove the battery 1, press the battery unlocking button 2
and pull the battery upward out of the power tool. Do not
exert any force.
Battery Charge-control Indication (see figure A)
The three green LEDs of the battery charge-control indicator
7 indicate the charge condition of the battery 1. For safety
reasons, it is only possible to check the status of the charge
condition when the machine is at a standstill.
Press button 6 to indicate the charge condition. This is also
possible when the battery 1 is removed.
LED
Continuous lighting 3 x green
Continuous lighting 2 x green
Continuous lighting 1 x green
Flashing light 1 x green
When no LED lights up after pushing button 6, then the
battery is defective and must be replaced.
these chargers are matched to the lithium-ion battery of
your power tool.
machine has been automatically switched off. The
battery can be damaged.
English | 11
Capacity
2/3
1/3
<1/3
Reserve
1 609 92A 3U5 | (10.7.17)
Publicidad
