Kemper 1650 Manual página 8

8. Before plugging the foam cutter into a socket, check whether your voltage corresponds to the rating label of
the appliance. Do not leave the foam cutter on, if you do not use it; it causes an early oxidation reaching
over-temperatures which could compromise the duration.
9. Before using the tool, control its integrity, if there are any defective parts or it has other conditions, which
could negatively influence its functions and safety.
10. Do not lean the metal parts of the foam cutter, if it is on (tips or resistances) on inflammable or perishable
materials at high temperatures (for ex.: plastic, rubber, wood).
11. Do not touch the metal parts of the foam cutter (tips or resistances) when it is on, with your hands or other
parts of the body. High temperatures can cause severe burns. Handle with care.
12. Use always the issued support to store the soft-solder when you do not use it, to avoid accidental contact
with the hot parts and the risk of fire.
13. After finishing the work, leave the foam cutter cool in the air before put it away; never put it under water to
avoid electric shocks.
14. Store the tool far from rain or humidity.
15. The tool has been designed for individual use.
16. Never connect the power cord to extensions or triple plugs. Do not pull or damage the power cord. Before
any maintenance operations, disconnect the plug from the mains socket.
17. If the appliance does not work properly, immediately turn off the fan heater and disconnect it from the mains
socket. For repairs, contact a technical support centre authorised by the manufacturer, and require that
original spare parts be used. Using parts that do not conform to the product may seriously compromise its
correct operation.
18. Do not use the tool if any part is damaged or defective.
19. This tool is not a toy.
INSTRUCTIONS FOR USE
1. Feeder
2. Support
3. Handle
A,B,C – Points.
1. Plug the appliance into a current socket with the following characteristics: 220-240 V, 50-60 Hz, c.a.
2. Choose the tip and insert on the foam cutter. Control that the tip is clean and the hole where it is inserted is free
from impurities. Before removing the tip, unplug the foam cutter from the electric supply and let it cool down.
Type of tips and applications:
A. HOT WIRE TIP – for cutting foam in sheet.
B. ENGRAVER TIP – to engraving with hot tip.
C. HOT KNIFE TIP – for cutting with cylindrical blade.
ATTENTION: Do not use not original spare parts.
Do not use a spare wire different from the one supplied, it can caused
damages to the card.
SAFETY MEASURES
ATTENTION: Place the tool on the support when you do not
1.
use it.
Do not use the tool on devices or conductors under voltage.
2.
Keep the tool away from inflammable materials. This tool can set fire to different materials, make a proof on
3.
a discarded material before use.
Disorder and scarce lighting could cause incidents. Keep the working area always clean and well-lighted.
4.
The electric resistance starts to warm up when the foam cutter is connected to the power supply. Do not touch
5.
the hot tip of the tool. Always remember the tool has a hot tip to avoid burns. Store it in the suitable support.
The possible exhalations coming from the material on which you are working can be dangerous. Ask for
6.
information about toxicity of the used materials and work in a well-airy area.
Handle with comfort the tool and proceed to cut without forcing the cutting. Let the heat of the tool do the job
7.
without forcing in order to avoid damages to the tools.
Do not let the foam cutter unattended when it is plugged to the electricity supply.
8.
MAINTENANCE
This appliance requires no maintenance except cleaning of its external surfaces. To clean external surfaces,
1.
use only a soft moistened cloth. Do not use solvents.
Before cleaning the appliance, set or change tips disconnect it from the mains socket and wait for it to cool
2.
down. Do not put the tool under liquid substances.
DT ISTR (1650) 4/2012_ REV. 7_07/2019
1650
8 /40