Metabo MS 18 LTX 15 Manual Original página 20

en ENGLISH
Fit accessories securely. If the machine is operated
in a holder: secure the machine well. Loss of control
can cause personal injury.
Bio sawing chain adhesive oil
100 ml: ... order no.: 628711000
1 l: .......... order no.: 628441000
Chain (as a replacement) Order no.: 628713000
Guide rail (as a replacement) Order no.:
628712000
Telescopic rod, order no.: 628714000
Chargers: SC 30, etc.
Battery packs with different capacities. Buy
battery packs only with voltage suitable for your
power tool.
4.0 Ah (LiHD), order no.: 625367000
etc.
2.0 Ah (Li-Ion), order no.: 625026000
4.0 Ah (Li-Ion), order no.: 625027000
etc.
For a complete range of accessories, see
www.metabo.com or the catalogue.
14. Repairs
Repairs to electrical tools must ONLY be
carried out by qualified electricians!
Only original Metabo spare parts should be used.
Contact your local Metabo representative if you
have Metabo power tools requiring repairs. For
addresses see www.metabo.com.
You can download a list of spare parts from
www.metabo.com.
15. Environmental Protection
Observe national regulations on environmentally
compatible disposal and on the recycling of disused
machines, packaging and accessories.
Packaging materials must be disposed of according
to their labelling in accordance with municipal
guidelines. Further information can be found at
www.metabo.com in the "Service" section.
Battery packs may not be disposed of with regular
waste. Return faulty or used battery packs to your
Metabo dealer!
Do not allow battery packs to come into contact with
water!
Only for EU countries: never dispose of
power tools in your household waste!
According to European Directive 2012/19/EU
on Waste from Electric and Electronic Equipment
and implementation in national law, used power
tools must be collected separately and recycled in
an environmentally-friendly manner.
Discharge the battery pack in the power tool before
disposal. Prevent the contacts from short-circuiting
(e.g. by protecting them with adhesive tape).
20
f 16. Technical Data
Explanatory notes on the specifications on page 3.
Subject to change in accordance with technical
progress.
U = Voltage of battery pack
L = Guide rail length
max
L = Usable blade cutting length
v = Chain speed in idling
K
n = Motor speed (idle)
0
K = Sawing chain, spacing
T
K = Sawing chain, number of driving links
A
K = Sawing chain, driving link thickness
T
m = Weight (without guide rail, sawing chain,
1
battery pack, sawing chain guard,
telescopic rod)
m = Weight (with guide rail, sawing chain,
2
battery pack, sawing chain guard,
telescopic rod)
Measured values determined in conformity with
EN 62841.
Permitted ambient temperature during operation:
-20 °C (-4°F) to 50 °C (120°F) (limited performance
with temperatures below 0 °C (32°F)). Permitted
ambient temperature for storage: 0 °C to 30 °C.
Recommended ambient temperature when
charging: 0 °C to 40 °C.
direct current
The technical specifications quoted are subject to
tolerances (in compliance with relevant valid
standards).
Emission values
These values make it possible to assess the
emissions from the power tool and to compare
different power tools. The actual load may be higher
or lower depending on operating conditions, the
condition of the power tool or the accessories used.
Please allow for breaks and periods when the load
is lower for assessment purposes. Arrange
protective measures for the user, such as
organisational measures based on the adjusted
estimates.
Vibration total value (vector sum of three directions)
determined in accordance with EN 62841:
a = Vibration emission value (sawing
h
hardwood trunk)
K = uncertainty (vibration)
h
Typical A-effective perceived sound levels:
L = sound pressure level
pA
L = acoustic power level
WA
K , K = uncertainty
pA WA/WA(G)
L = guaranteed acoustic power level as
WA(G)
per 2000/14/EC
During operation the noise level can exceed
80 dB(A).
Wear ear protectors!