Skil 6310 Instrucciones página 6

GB
INTRODUCTION
•
This tool is intended for hammer drilling in brick,
concrete and stone as well as for drilling in wood, metal,
ceramic and plastic; tools with electronic speed control
and left/right rotation are also suitable for screwdriving
and thread cutting
TECHNICAL SPECIFICATIONS 1
OPERATING CONTROLS 2
A Switch for on/off and speed control
B Button for switch locking
C Switch for changing direction of rotation
D Switch for selecting drilling function
SAFETY
•
Read and save this instruction manual (pay special
attention to the safety instructions at the back)
•
Avoid damage that can be caused by screws, nails and
other elements in your workpiece; remove them before
you start working
•
Always keep the cord away from moving parts of the tool
•
When you put away the tool, switch off the motor and
ensure that all moving parts have come to a complete
standstill
•
Use completely unrolled and safe extension cords with a
capacity of 16 Amps (UK 13 Amps)
•
In case of electrical or mechanical malfunction,
immediately switch off the tool and disconnect the plug
•
SKIL can assure flawless functioning of the tool only
when original accessories are used
•
Before using accessories always compare the maximum
allowed r.p.m. of that specific accessory with the r.p.m.
of the tool
•
This tool should not be used by people under the age of
16 years
•
Be careful not to drill or drive into areas where electrical
wires may be contacted
•
The noise level when working can exceed 85 dB(A);
wear ear protection
•
If the cord is damaged or cut through while working, do
not touch the cord, but immediately disconnect the plug
•
Never use tool when cord is damaged; have it replaced
by a qualified person
•
Always check that the supply voltage is the same as the
voltage indicated on the nameplate of the tool (tools with
a rating of 230V or 240V can also be connected to a
220V supply)
•
If the drill bit becomes unexpectedly jammed (causing a
sudden, dangerous reaction), immediately switch off the
tool
•
Be aware of the forces that occur as a result of jamming
(especially when drilling metals); always hold the tool
firmly with both hands and take a secure stance
•
Always disconnect plug from power source before
making any adjustment or changing any accessory
WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):
•
Do not connect the blue (= neutral) or brown (= live) wire
in the cord of this tool to the earth terminal of the plug
•
If for any reason the old plug is cut off the cord of this
tool, it must be disposed of safely and not left
unattended
USE
•
On/Off 3
•
Switch locking for continuous use 4
•
Speed control for smooth starting 5
•
Changing direction of rotation 6
- when not properly set in left/right position, switch A
cannot be activated
! change direction of rotation only when tool is at a
complete standstill
•
Normal drilling/screwdriving versus hammer drilling 7
! select drilling function only when tool is switched
off
•
Changing bits 8 9
- insert the bit as deep as possible in the chuck
! do not use bits with a damaged shank
•
Adjusting drilling depth 0
•
Holding and guiding the tool ! @
- keep the ventilation slots uncovered
- do not apply too much pressure on the tool;
let the tool do the work for you
APPLICATION ADVICE
•
Use the appropriate bits #
! only use sharp bits
•
When drilling ferrous metals
- pre-drill a smaller hole, when a large hole is required
- lubricate drill bit occasionally with oil
•
When turning in a screw at/near the cross cut end or an
edge of wood, pre-drill a hole in order to avoid cracking
of the wood
•
Splinterfree drilling in wood $
•
Dustfree drilling in walls %
•
Dustfree drilling in ceilings ^
•
Drilling in tiles without skidding &
•
For more tips see www.skileurope.com
GUARANTEE / ENVIRONMENT
•
Always keep tool and cord clean (especially the
ventilation slots)
! disconnect the plug before cleaning
•
This SKIL product is guaranteed in accordance with
statutory/country-specific regulations; damage due to
normal wear and tear, overload or improper handling will
be excluded from the guarantee
•
In case of a complaint, send the tool undismantled
together with proof of purchase to your dealer or the
nearest SKIL service station (addresses as well as the
service diagram of the tool are listed on
www.skileurope.com)
•
Dispose of the tool by sorting tool, accessories and
packaging for environment-friendly recycling (the plastic
components are labeled for categorized recycling)
6