Milwaukee M18 BLCS66-0X Manual Original página 24

TECHNICAL DATA
Circular saw
Production code
Battery voltage
No-load speed
Saw blade dia. x hole dia
Saw blade thickness
Blade teeth
Max. Cutting depth at 0° / 45° / 50°
Weight according EPTA-Procedure 01/2014 (Li-Ion 2,0 Ah ... 5,0 Ah)
Recommended Ambient Operating Temperature
Recommended battery types
Recommended charger
Noise information
Measured values determined according to EN 62841. Typically, the A-weighted noise levels of the tool are:
GB
Sound pressure level (Uncertainty K=3dB(A))
Sound power level (Uncertainty K=3dB(A))
Wear ear protectors!
Vibration information
Vibration total values (triaxial vector sum) determined according to EN 62841
Sawing of wood (Li-Ion 2,0 Ah): Vibration emission value a
Uncertainty K=
WARNING
The vibration and noise emission level given in this information sheet has been measured in accordance with a standardized test given in
EN 62841 and may be used to compare one tool with another. It may be used for a preliminary assessment of exposure.
The declared vibration and noise emission level represents the main applications of the tool. However if the tool is used for di erent
applications, with di erent accessories or poorly maintained, the vibration and noise emission may di er. This may signi cantly increase
the exposure level over the total working period.
An estimation of the level of exposure to vibration and noise should also take into account the times when the tool is switched o or when
it is running but not actually doing the job. This may signi cantly reduce the exposure level over the total working period.
Identify additional safety measures to protect the operator from the e ects of vibration and/or noise such as: maintain the tool and the
accessories, keep the hands warm, organization of work patterns.
Wear ear protectors. Exposure to noise can cause hearing loss.
WARNING Read all safety warnings, instructions,
illustrations and speci cations provided with this power tool.
Failure to follow all instructions listed below may result in electric
shock, re and/or serious injury.
Save all warnings and instructions for future reference.
CIRCULAR SAW SAFETY WARNINGS
Cutting procedures
a) DANGER: Keep hands away from cutting area and
the blade. Keep your second hand on auxiliary handle, or
motor housing. If both hands are holding the saw, they cannot be
cut by the blade.
b) Do not reach underneath the workpiece. The guard cannot
protect you from the blade below the workpiece.
c) Adjust the cutting depth to the thickness of the work-
piece. Less than a full tooth of the blade teeth should be visible
below the workpiece.
English Deutsch
22
h,W
d) Never hold the workpiece in your hands or across
your leg while cutting. Secure the workpiece to a stable
platform. It is important to support the work properly to minimise
body exposure, blade binding, or loss of control.
e) Hold the power tool by insulated gripping surfaces,
when performing an operation where the cutting accessory
may contact hidden wiring. Contact with a „live" wire will also
make exposed metal parts of the power tool „live" and could give
the operator an electric shock.
f) When ripping, always use a rip fence or straight edge
guide. This improves the accuracy of cut and reduces the chance
of blade binding.
g) Always use blades with correct size and shape (diamond
versus round) of arbour holes. Blades that do not match the
mounting hardware of the saw will run o -centre, causing loss of
control.
M18 BLCS66
4679 20 04 ...
... 000001-999999
18 V
5000 min
-1
190 x 30 mm
1,6 mm
24
66 / 48 / 46 mm
3,7...4,0 kg
-18°C ... +50°C
M18B2...M18B5
M1418C6; M12-18...
83,2 dB(A)
94,2 dB(A)
2,0 m/s2
1,5 m/s2