Westin Automotive Products 27-1785 Instrucciones

AUTOMOTIVE PRODUCTS, INC.
MOUNT KIT
EQUIPO DE MONTAJE
JEU DE MONTAGE
27-1785
STEP BOARD
ESTRIBOS
MARCHEPIED
27-0000 27-0005
27-6120 27-6125
27-6520
ITEM QTY CONTENTS -
1,2 2 STEP BOARD, PASSENGER (1) AND DRIVER (2) (SOLD SEPARATELY)
3 4 MOUNT BRACKET
4 8 5/16-18 X .75" SQUARE HEAD BOLT
5 8 5/16" FLAT WASHER
6 8 5/16-18 LOCK NUT
7 12 M8-1.25 X 30MM HEX HEAD BOLT
8 20 8MM FLAT WASHER
9 12 8MM LOCK WASHER
10 8 M8-1.25 HEX NUT
11 4 M8-1.25 EXTRUDED U-NUT
1,2 2 ESTRIBOS, ACOMPAÑANTE (1) CONDUCTOR (2) (SE COMPRA SEPARADO)
3 4 SOPORTE
4 8 PERNOS CON CABEZA CUADRAD 5/16-18 X .75"
5 8 ARANDELAS DE PRESIÓN DE 5/16
6 8 TUERCA PRESIÓN DE 5/16-18
7 12 PERNOS CON CABEZA HEXAGONAL M8-1,25 X 30MM
8 20 ARANDELAS PLANAS DE 8MM
9 12 ARANDELAS DE PRESIÓN DE 8MM
10 8 TUERCAS HEXAGONALES DE M8-1,25
11 4 TUERCA EN "U" M8 - 1,25
1,2 2 MARCHE-PIEDS, PASSAGER (1) ET CONDUCTEUR (2) (ACHETE
SEPAREMENT)
3 4 SUPPORT
4 8 BOULON A TETE CARREE 5/16-18 X .75 PO
5 8 RONDELLES PLATES 5/16 PO
6 8 ECROU A FREIN 5/16-18
7 12 BOULON A TETE HEXAGONALE M8-1,25 X 30MM
8 20 RONDELLE PLATE 8MM
9 12 RONDELLE A FREIN DE 8MM
10 8 ECROU HEXAGONAL M8-1,25
11 4 ECROU EN U M8-1,25
STEP 1.
Remove contents from box and check for damage. Verify all parts are present. Read and understand instructions before beginning.
STEP 2.
Both front and rear brackets are the same for each side.
STEP 3.
Locate driver side mounting locations on vehicle.
STEP 4.
Attach brackets to underside of rocker panel as shown. Hand tighten.
For Jeep Commanders only:
Remove the shroud to gain access to top mounting location on the bracket. After bracket is installed and fasteners are tightened, reattach shroud
with the four existing bolts previously removed.
STEP 5.
Insert square head bolts as shown (2 per slot, 4 per Step board/Running board).
board/Running board, run wiring harness prior to attaching step board to brackets (Refer to Step 5).
harness on passenger side.
STEP 6.
For Aluminum Running boards (if desired): Slide closure strip as shown. Set lights (if included) in appropriate location. Attach to running board as
shown. SEE FIGURE 3.
STEP 7.
Attach Step board / Running board to brackets as shown. Make sure step board and brackets are properly aligned and tighten fasteners.
Recommended torque values are 10 FT.LBS. for 5/16" square head fasteners, 23 FT.LBS. for 8mm fasteners, and 19 FT.LBS. for factory 8mm
bolts. SEE FIGURE 7.
Proceed to Steps 4 and 5.
WARNING: INSTALLING LIGHT HARNESS REQUIRES SPLICING INTO VEHICLES ELECTRICAL SYSTEM. WESTIN RECOMMENDS
USING A PROFESSIONAL FOR THIS INSTALLATION. NOTE: AVOID AREAS OF EXCESSIVE HEAT, VIBRATION, PINCH OR
ROTATION WHEN SECURING HARNESS TO VEHICLE. CAUTION: ALWAYS USE A FUSED(+) POSITIVE SUPPLY SOURCE.
UNDERCOAT SEAL FOR HARSH WEATHER.
INSTRUCTIONS-INSTRUCCIONES-CONSIGNES
APPLICATION: 2005-07 JEEP GRAND CHEROKEE
APLICACIÓN:
APPLICATION: JEEP GRAND CHEROKEE 2005-07
1 1
CONTENIDO - CONTENU
"
SEE FIGURE 1.
To attach the passenger side front bracket, remove the four bolts that secure the rear air and heat line shroud.
SEE FIGURE 9.
Drill hole through plastic strip and run wires as shown.
NOTE: For lighted version of Step board, remove plastic cover from each end of under side of Step board.
2006-07 JEEP COMMANDER
JEEP GRAND CHEROKEE
JEEP COMMANDER , MOD. 2006-07
JEEP COMMANDER 2006-07
SEE FIGURES 1 AND 2.
SEE FIGURES 4 AND 5 NOTE:
SEE FIGURE 6.
WO:
, MOD. 2005-07
3
TOOLS-HERRAMIENTA-OUTILS
TWO 13MM WRENCH
1/2" SOCKET
RATCHET
TORQUE WRENCH
DOS LLAVE DE TUERCAS DE 13MM
DADO DE 1/2"
MANERAL
LLAVE DE TORQUE
DEUX CLE 13MM
DOUILLE 13MM
CLIQUET
CLE DE COUPLE
. For lighted Step
SEE FIGURES 4, 5 AND 8.
75-0777 REVISION B 4/3/07
Run longer wire