Stanley STP18 Manual De Instrucciones página 35

c. Disconnect the plug from the power source and/
or remove the battery pack, if detachable, from the
power tool before making any adjustments, changing
accessories, or storing power tools. Such preventive
safety measures reduce the risk of starting the power
tool accidentally.
d. Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the power
tool or these instructions to operate the power tool.
Power tools are dangerous in the hands of untrained
users.
e. Maintain power tools and accessories. Check for
misalignment or binding of moving parts, breakage
of parts and any other condition that may affect the
power tool's operation. If damaged, have the power
tool repaired before use. Many accidents are caused
by poorly maintained power tools.
f. Keep cutting tools sharp and clean. Properly maintained
cutting tools with sharp cutting edges are less likely to
bind and are easier to control.
g. Use the power tool, accessories and tool bits etc.
in accordance with these instructions, taking into
account the working conditions and the work to be
performed. Use of the power tool for operations different
from those intended could result in a hazardous situation.
h. Keep handles and grasping surfaces dry, clean and
free from oil and grease. Slippery handles and grasping
surfaces do not allow for safe handling and control of the
tool in unexpected situations.
5. Service
a. Have your power tool serviced by a qualified repair
person using only identical replacement parts. This
will ensure that the safety of the power tool is maintained.
ADDITIONAL SPECIFIC SAFETY RULES
Safe operation
♦ Wear protective hair covering to contain long hair.
♦ When not in use, tools should be stored in a dry locked-up
place, out of reach of children.
♦ Never use the machine without the appropriate guard in
place and correctly adjusted.
♦ Do not use knives which are blunt as this increases the
danger of kickback
♦ Do not to do the following operations:
– stopped work (i.e. any cut which does not involve the
full work piece length);
– recesses, tenons or moulds; and
– planing of badly bowed wood where there is
inadequate contact on the infeed table.
♦ To avoid injury, never rotate the cutterhead directly with
your hands.
♦ Keep hands away from the underside of the
cutterhead carriage.
♦ Never clear clogs, make cutter knife replacement, or any
other repairs/adjustments with unit plugged in.
♦ Make certain that the switch is in the "OFF" position before
connecting plug to a power source.
♦ Stay alert—never operate the unit when tired or under
the influence of drugs, alcohol, or medication.
♦ Do not use in dangerous environments. Do not use
near flammable substances, in damp or wet locations,
or expose to rain.
♦ Never plane material which is shorter than 304.8 mm (12")
narrower than 19.05 mm (3/4"), or wider than 304.8 mm
(12") or thinner than 12.7 mm (1/2").
♦ Exhaust chute: remove shavings with brush or vacuum
after power has been shut off and cutterhead has
stopped rotating.
♦ Always locate planer with proper clearance on the outfeed
side of the unit to prevent pinching or binding of the
workpiece against any obstacle.
♦ Maintain the proper relationships of infeed and outfeed
table surfaces and cutterhead knife path.
Additional Safety Information
WARNING: We recommend the use of a residual
current device with a residual current rating of 30mA
or less.
RESIDUAL RISKS
In spite of the application of the relevant safety regulations
and the implementation of safety devices, certain residual
risks cannot be avoided. These are:
– Impairment of hearing
– Risk of personal injury due flying particles.
– Risk of burns due to accessories becoming hot during
operation.
– Risk of personal injury due to prolonged use.
– Risk of dust from hazardous substances.
LABELS ON TOOL
In addition to the pictographs used in this manual, the labels
on the tool show the following pictographs:
WARNING! To reduce the risk of injury, the user
must read the instruction manual before use.
Wear ear protection.
Wear safety glasses or goggles.
Wear a dust mask.
Do not expose the tool to rain or high humidity
or leave outdoors while it is raining.
WARNING logo for transport: do not carry or
use it as handle
English (original instruction)
35