Descargar Imprimir esta página

Exo Terra TERRASKY Manual De Instrucciones página 4

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 13
fixture are undamaged before putting it into operation.
2. Position the TerraSky on your Terrarium. On Exo Terra Natural
Terrariums, the mounting brackets can be secured between
the outer terrarium rim and the screen top (p 45, see image A).
For installation on regular terrariums, simply place the TerraSky
on the terrarium and adjust the extendable brackets so they
press against the outside of the terrarium rim. (see image B on
page 45)
3. Connect the connector of the power adaptor to the connector
of the fixture.
4. Connect the power adaptor to the wall receptacle.
Remote Control
1. Remove plastic cover from wireless remote; remove the clear
plastic tab located at the bottom of the remote to activate the
battery connection.
2. Point the remote control in the direction of the TerraSky, and
push the ON/OFF button.
Remote Control Keypad Functions (p. 46-47)
1. Simply push any of the pre-programmed color spectrum buttons
to switch between the 6 different base color settings. These
pre-programmed color spectrums are the most commonly used
color spectrums for terrariums. They also form the base from
which you can start custom blending your own preferred color
spectrum (see step 2 and 3).
2. To fine-tune these base color settings, simply press any of the
+ or - color buttons (red-green-blue-white) to adjust the RGBW
LED's output. Each individual RGBW color can be increased or
decreased in output strength or even shut off completely by
6
using the + or - color buttons to create the perfect light color for
your application.
3. If you are satisfied with the result of your customised color
setting: press and hold any of the 4 customisable preset buttons
(P1-P2-P3-P4) for 4 seconds to store your customised color
setting. The TerraSky will flash once, once the setting is stored.
Repeat as desired until all 4 customisable preset buttons have
been programmed.
4. To simulate Moon Lighting, there are 3 different Moon Light
buttons to choose from, depending on the Moon Cycle you would
like to use at night.
5. To simulate Cloud Cover during daytime, there are 4 different
Cloud Cover strength buttons to choose from, depending on
whether you would like lightly clouded sky or up to dark stormy
clouds.
6. To simulate Storm Effects, there are 3 different Storm Effect
strengths to choose from. Going from lightly clouded sky with
the occasional lightning, up to dark stormy clouds with lots of
lightning.
7. With the Play/Pause button, you can play or pause any dynamic
light effect.
8. The Sunrise/Sunset button allows you to simulate a gentle
Sunrise or Sunset lighting effect. Without pushing the ON button,
simply push the Sunrise/Sunset button in the morning to start
the Sunrise. Push the Sunrise/Sunset once again in the evening
to start the Sunset.
9. The Color Spectral Cycle button will slowly cycle through every
color spectrum.
Change the Remote's Battery
The battery compartment is located on the back of the remote and
can be opened by squeezing and holding the "release tab" while
gently pulling out the battery holder. Remove the empty battery and
replace with a 3V (CR2025) lithium cell battery. Gently push the
battery holder back into the slot.
MAINTENANCE
For maximum LED performance, it is recommended that the
fixture and the LED lens be cleaned on a weekly basis. Unplug the
transformer prior to cleaning the light fixture and remove it from the
terrarium. Use both hands when manipulating this appliance. Wipe
exposed surfaces carefully with a damp cloth to remove any dust or
mineral deposits that may collect over time. Do not use detergents
or harsh cleaners as it can damage the light fixture. Make sure all
surfaces are dry before re-connecting the transformer to the power
source.
BASIC TROUBLESHOOTING
If the TerraSky does not light up when you press the ON/OFF button,
please check the following:
1. Ensure that all plugs and wires are firmly connected:
a. Check the connection from the fixture to the power adaptor.
b. Check the connection from the power adaptor to the wall
receptacle.
2. Check if the battery of the Remote Control has sufficient power. If
not, please replace the battery.
GUARANTEE
This product is guaranteed for defective parts and workmanship
for a period of 2 years from the date of purchase. This guarantee is
valid with proof of purchase only. The guarantee is limited to repair
or replacement only and does not cover consequential loss, loss or
damage to livestock and personal property or damage to animate or
inanimate objects, irrespective of the cause thereof. This guarantee
is valid only under normal operating conditions for which the unit
is intended. It excludes any damage caused by unreasonable use,
negligence, improper installation, tampering, abuse or commercial
use. The warranty does not cover wear and tear, breakage of glass or
parts which have not been adequately or correctly maintained. THIS
DOES NOT AFFECT YOUR STATUTORY RIGHTS.
RECYCLING
This item bears the selective sorting symbol for waste
electronic and electrical equipment (WEEE). This
means that the product must be handled pursuant to
European Directive 2012/19/EU in order to be recycled or
dismantled to minimize its impact on the environment. For
further information please contact your local or regional
authorities. Electronic products not included in the selective sorting
process are potentially dangerous for the environment and human
health due to the presence of hazardous substances.
SERVICE
If you have any problem or question about the operation of this
product, please consult your Exo Terra
®
instance. Most problems can be resolved in store, but in the unlikely
event it cannot, please return the unit with a valid proof of purchase
specialist retailer in the first

Publicidad

loading

Este manual también es adecuado para:

Pt2413