Publicidad
Idiomas disponibles
Idiomas disponibles
Clean the product at regular intervals using a damp cloth and
a little soft soap. Do not use any cleaning products or solvents;
they could attack the plastic parts of the product. Make sure
that no water can penetrate the motor.
• We recommend regular inspections and care for a long ser-
vice life (i. e. at least once a month).
• Before extended periods of inactivity or through the winter,
the garden pump and domestic waterworks should be thor-
oughly flushed through with water, emptied completely and
then stored dry.
• To empty the housing, loosen the water drain screw (9) and
tilt the garden pump and domestic waterworks slightly.
• If there is a risk of frost the garden pump and domestic wa-
terworks must be completely emptied.
• After longer periods of storage check the pump by switching
on/off briefly in order to check that the rotor turns normally.
• In the event of the garden pump and domestic waterworks
being jammed connect the pressure line to the water supply
line and remove suction hose. Open the water supply line.
Switch the garden pump and domestic waterworks on for
ca. two seconds several times. This method rectifies block-
ages in most cases.
• To clean the pre-filter (12) unscrew the pre-filter locking
screw (11) and remove it. Afterwards, clean it with clear
water.
Connections and repairs
Connections and repair work on the electrical equipment may
only be carried out by electricians.
Service information
With this product, it is necessary to note that the following parts
are subject to natural or usage-related wear, or that the follow-
ing parts are required as consumables.
Wearing parts*:Seals, pre-filter, flow sensor impeller, non-re-
turn valve
* may not be included in the scope of supply!
Spare parts and accessories can be obtained from our Service
Centre. To do this, scan the QR code on the front page.
13. Storage
Store the device and its accessories in a dark, dry and frost-free
place that is inaccessible to children.
The optimum storage temperature is between 5 and 30˚C.
Store the electric tool in its original packaging.
Cover the electric tool to protect it from dust or moisture.
Store the operating manual with the electric tool.
14. Electrical connection
The electrical motor installed is connected and
ready for operation. The connection complies with
the applicable VDE and DIN provisions. The cus-
tomer's mains connection as well as the extension
cable used must also comply with these regula-
tions.
8
GB/IE
14.1 Damaged electrical connection cable
The insulation on electrical connection cables is often dam-
aged.
This may have the following causes:
• Pressure points, where connection cables are passed through
windows or doors.
• Kinks where the connection cable has been improperly fas-
tened or routed.
• Places where the connection cables have been cut due to
being driven over.
• Insulation damage due to being ripped out of the wall outlet.
• Cracks due to the insulation ageing.
Such damaged electrical connection cables must not be used
and are life-threatening due to the insulation damage.
Check the electrical connection cables for damage regularly.
Ensure that the connection cables are disconnected from elec-
trical power when checking for damage.
Electrical connection cables must comply with the applicable
VDE and DIN provisions. Only use connection cables of the
same designation.
The printing of the type designation on the connection cable
is mandatory.
If the mains connection cable of this device is damaged, it must
be replaced by a special connection cable which can be ob-
tained from the manufacturer or its service department.
AC motor 230 V∼ / 50 Hz
Mains voltage 230 V∼ / 50 Hz.
Mains power connection and extension leads must be 3-core =
P + N + SL. - (1/N/PE).
Extension cables up to 25 m long must have a cross-section of
1.5 mm². The mains power connection must be protected with
a max. 16 A fuse.
Please provide the following information in the event of any
enquiries:
• Type of current for the motor
• Engine data - type plate
15. Disposal and recycling
The device is supplied in packaging to avoid transport dam-
ages. This packaging is raw material and can thus be used
again or can be reintegrated into the raw material cycle.
The device and its accessories are made of different materials,
such as metal and plastic. Take defective components to spe-
cial waste disposal sites. Check with your specialist dealer or
municipal administration!
The packaging is made of environmentally friend-
ly materials that can be disposed of at your local
recycling centre.
You can find out how to dispose of the disused de-
vice from your local authority or city administra-
tion.
Publicidad
