Descargar Imprimir esta página

Alpine AS 5148 Li Manual De Uso Y Mantenimiento página 18

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 89
E. Led lights
F.
Handle pivot closure
G. Central handle
H. Ignition key
I.
Exhaust chute
Deflector
J.
K. Auger
L. Auger compartment
M. Wheel
N. Lower blade
O. Transport handle
P.
Lower part of handle
Q. Cable gland
R. Battery compartment
S. Battery charger (supplied separately)
T.
Battery (supplied separately)
4. ASSEMBLY
For storage and transport purposes, some 
components of the machine are not installed 
in the factory and have to be assembled after 
unpacking. Follow the instructions below.
4.1 ASSEMBLY COMPONENTS
The packaging holds the components needed 
for assembly (fig. 4  )  listed in the following table:
Component
Snow thrower
Discharge chute
adjustment handle
Handle
Handle fitting
Spacers and screws for 
securing the handle in place
Spacers and screws for 
securing the handle in place
Ignition key
Cable gland to handle
Deflector
Instructions
4.2 UNPACKING
1. Cautiously  open  the  packaging,  paying 
attention not to lose components.
2. Consult  the  documentation  in  the  box, 
including these instructions.
3. Remove  all  the  unassembled  parts  from  the 
box.
4. Lift the snow thrower from the box.
Fig.
N.
4
1
4.A, 4.A1,
1
4.A2
4.B
1
4.C
1
4.D, 4.E
2
4.F, 4.G
4
4.H
1
4.I
1
4.J
1
-
1
EN - 7
5. Dispose  of  the  box  and  packaging  in 
compliance with local regulations.
4.3 HANDLE ASSEMBLY
1. Assemble  the  central  part  of  the  handle 
(fig.  4.C)  on  the  snow  thrower  (lower  part  of 
handle), fastening it with screws (fig. 4.D, 4.E) 
on both sides.
2. Position  the  upper  handle  (fig.  4.B)  on  the 
central  one  and  fasten  it  with  the  specific 
screws and fastenings (fig. 4.G, 4.F).
3. Fasten  the  electrical  cable  in  place  with  the 
specific cable gland (fig. 4.I).
4.4 DISCHARGE CHUTE ADJUSTMENT
HANDLE ASSEMBLY
1. Assemble  the  handle  (fig.  5.A1)  using  the 
specific  extension  shaft  (fig.  5.A),  fastening 
it in place with the 2 screws (fig. 5.A2).Make 
sure the holes of the shaft (fig. 5.A) and joint 
(fig. 5.A1) are aligned.
2. Insert the 2 screws in the holes and fix.
3. Pass the handle obtained in the specific lower 
handle support (fig. 5.B).
4. Insert  the  end  of  the  handle  in  the  specific 
coupling hole on the chute, keeping it straight 
and with the grip upwards (fig. 5.C).
5. Check  the  discharge  chute  by  turning  it 
entirely  in  both  directions.  The  chute  must 
freely rotate (fig. 9  ) .
4.5 DEFLECTOR ASSEMBLY
1. Insert  the  deflector  on  the  discharge  duct  in 
the upright position (fig. 6.A).
2. Fit the tabs on both sides in the rotation
eyelets (fig. 6.B).
3. Push  until  the  pins  fit  into  the  specific  holes 
with a click.
4.6 CABLE GLAND ASSEMBLY
Insert the cable in the cable gland
(fig. 4.I) and fit it on the intermediate handle.
5. CONTROLS
5.1 IGNITION KEY
Used to start and stop the motor. The 
ignition key has two positions (fig. 8.H):
1. Key  removed  -  OFF  -  the  motor  stops  and 
cannot be restarted.
2. Key  inserted  -  ON  -  the  motor  can  start  and 
run.

Publicidad

loading

Este manual también es adecuado para:

St 515 li