La Nordica FALO Manual Del Usuario página 14

FAN ELECTRIC CONTROLLER - 0020800 - B
The fan electric controller allows for the simple and intuitive selection of the speed of the convection air dissipated into the environment of
our solid combustion wood product. The controller must be placed away from nozzles or from the main heat source; if placed in the counter
hood, it must be positioned in a low heat point. Simple installation is guaranteed by the the fact that it can be fitted in classic recessed
electrical boxes commonly found in buildings, or it can be wall-mounted.
The controller activates ventilation in MANUAL/AUTOMATIC/COMFORT mode, which can be selected on the controller display by pressing/
touching the keys.
Control OPERATION.
The device is switched on and off by pressing/touching the ON/OFF key. When off,
OFF is displayed and the light of the ON/OFF key is on.
Press the MENU key to access the Menu.
Use the on/off key to go from the OFF status to the ON status. The operating mode
and the set speed will be displayed.
MANUAL mode.
In MANUAL MODE, when the words "MANUAL OPERATION" are displayed,
the motor is activated at the set speed. The speed can be set by means of
the UP and DOWN keys, which will show a minimum and maximum on the
progression bar on the display; when the key is released, the value is set
automatically.
AUTOMATIC mode.
In AUTOMATIC MODE, when the words "AUTO FUNCTION" are displayed; the motor is activated when the TM (Minimum start thermostat)
closes, thus when the starting temperature has been reached. It turns off when the temperature drops below this value. The flashing bar on
the display indicates that the TM has not reached the starting temperature (ventilation stopped); when the temperature has been reached,
the bar will become fixed (ventilation active). The desired speed, also in this mode, can be set using the UP and DOWN keys both in flashing
mode and in fixed mode (ventilation stopped or active).
COMFORT mode.
In COMFORT MODE, the controller follows the same dynamics of AUTOMATIC mode, but it is possible to shift a speed when the desired
temperature has been reached, which is shown and can be set on the display by using the UP key pressed for 2 seconds accessing a sub-
menu which displays "SET COMFORT" and this can be set using the UP and DOWN key, selecting the desired temperature between and°C.
The temperature is detected by the sensor on the front of the device (ambient temperature).
REDUCED SPEED mode.
In REDUCED SPEED MODE, when the UP and DOWN keys are pressed for 2 seconds, the set speed is reduced in any pre-set factory operating
condition (MANUAL/AUTOMATIC/COMFORT). This condition is displayed with an icon representing a fan. To go back to the normal ventilation
condition, press the UP and DOWN keys again for 2 seconds; the fan on the display will disappear and ventilation will go back to full power
at the set speed.
MENU.
Press the MENU key for 2 seconds to access the Menu, where it is possible to change, using the arrows:
• the LANGUAGE between ITALIANO, ENGLISh, DEUTSCh, FRANCAIS, ESPANOLA
• the BRIGhTNESS of the display from % to 100%
• TEMP UNIT: where it is possible to select the unit of measurement of the temperature CELSIUS or FAhRENhEIT
• ADJ TEMP: to calibrate the ambient temperature. It is possible to select a value between -10.0 and +10
REMOTE CONTROL OPERATION
The electronic controller for fan can be managed by means of an IR remote control.
When the controller is off, only the ON key is operational.
The device is turned on and off by pressing the ON-OFF key.
To access the operating mode selection menu, press the MENU key.
Press the MENU key again to select AUTOMATIC, MANUAL or COMFORT mode and wait 2
seconds to confirm.
In MANUAL mode only the keys of the SPEED SETTINGS group are active, to select one of the five
speeds.
In AUTOMATIC mode the keys of the SPEED SETTINGS group to select one of the five speeds and
the keys of the COMFORT TEMPERATURE SETTINGS group to adjust the COMFORT set are active.
14
:
ENGLISH
.
COMFORT
TEMPERATURE
SETTINGS
SPEED
SETTINGS
MENU
ON-OFF
REMOTE CONTROL
Battery CR2032