Hubix SECRA-1 Manual De Uso página 10

5. PRECAUTION IN USE
The helmets should not be used in situations where there is a risk which could
partially reduce its insulating properties. Follow the requirements of the live work
organization instructions.
6. PRECAUTION AFTER USE
If the helmet or face shield becomes dirty or contaminated, particularly their external
surfaces, they should be thoroughly cleaned in accordance with the manufacturer's
recommendations (see 8.)
7. STORAGE AND TRANSPORT
The helmet must be stored and transported in a special transport bag or other
protective packaging. During storage or transport, the face shield should be hidden
inside the helmet. Keep the helmet away from any sources of heat. Protect the
helmet against mechanical damage, compression, sunlight (UV), humidity, exhaust
gases, etc. Do not place the helmet in direct vicinity of windows or car windows. The
recommended storage temperature is 20±15°C
8. CLEANING AND DISINFECTION:
The hard hat and face shield should be cleaned after each use, which enables
precise control and prevents skin irritation of the user. The hard hat should be
cleaned only with soap and water. Do not use any solvents, detergents and
abrasives for cleaning. The sweatbands must be regularly replaced.
The face shield should be cleaned only with soap and water. After washing, dry the
shield properly. To clean the surface of shield visor, use a microfiber cloth, attached
to each helmet.
CAUTION! The face shield can be damaged by certain aggressive chemical
substances. Do not use any solvents or detergents and abrasives to clean the
face shield.
9. SPARE PARTS
Parts of the helmet that are very worn or damaged must be replaced with new ones.
The manufacturer provides full service of the product it offers and its dedicated
accessories. The users can replace damaged elements of the helmet by themselves or
send the helmet with a damaged part to the manufacturer.
List of spare parts to be replaced by the user himself:
H058S-PC front sweatband
H058S-PT rear sweatband
H058S-WZ head harness, complete
H058S-PS chinstrap with safety catches, complete
H058S-1-SZW1 face shield ARC-W1, complete
H058S-CL visor cleaning cloth
H058S-WR storage and transport bag
The latest instructions are available at www.secra.pl
10. REPLACEMENT OF SPARE PARTS
SWEATBAND
The sweatbands (Fig. 9) are fixed to the main strap – front sweatband (1) and the
back strap – back sweatband (2) using Velcro fasteners. In order to replace the front
sweatband, remove the six Velcro, which fasten it around the headband. In order to
replace the back sweatband, grab it and separate them from the regulator by gently
pulling them. In place of worn sweatband attach new ones.
HARNESS
In order to change the harness (Fig. 10), put a flat screwdriver (3 mm wide)
between the rim and the attachment of the harness. Then lightly pull the screwdriver
until the attachment of the harness becomes opened (1). Perform the same
procedure on all the attachments. After releasing all four attachments, grasp them
and pull gently (2) to separate the harness from the rim of the helmet (Fig.11).
In order to replace a damaged harness with a new one, insert the attachments of the
harness in the openings of the rim, push them one after another until a clicking sound
can be heard, and then check if they have been fastened properly.
CHIN STRAP
In order to change the chinstrap (Fig.12), grasp the attachment of the chinstrap (1)
and separate it from the anchorage on the rim of hard hat by pulling it with force.
Perform the same procedure on the remaining attachments. Replace the new one in
place of the damaged chinstrap.
Insert the attachments of chin strap (2) on the anchorage of the rim (3) and then pull
them up (Fig. 13) until securing the attachments (Fig. 14).
FACE SHIELD
The replacement of face shields is included in a separate manual.
11. ADDITIONAL ACCESSORIES
Optionally, additional accessories can be attached to the helmet:
H058S-AD2 two adapters for mounting on the helmet of earmuff, mounted by the
manufacturer or for self-assembly
H058S-OS earmuff, for mounting on adapters for self-assembly
H058S-LT flashlight, for self-assembly
H058S-AEP arcflash ear protectors, for self-assembly
Original Buff balaclava
Information on additional accessories and the manner of their installation are
contained in separate manuals
The latest instructions are available at www.secra.pl