Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
GUIDELINES FOR EXTENSION CORD USE
Extension cords are only to be used for temporary purposes.
They do not replace the need for installation of outlets and
proper wiring where necessary.
In the shop and on construction sites:
1. Extension cords with an equipment
grounding conductor must be used at all times.
2. Extension cords must be protected from damage,
and not run through doorways or windows where the
doors or windows may close, causing damage to the cord.
3. Extension cords should be a minimum of 16 AWG
and be rated for the equipment in use.
4. Extension cords must be periodically inspected
to ensure that the insulation and conductivity of the
wires are not compromised.
5. Extension cords should not be run through water or allowed to
have connections that may be exposed to accumulated water
TABLE 1
Nameplate
Amperes
25'
@120 V
0 -5
16
5.1 - 8
16
8.1 -12
14
12.1 - 16
12
NR – Not Recommended
WARNING:
This product can expose you to chemicals including lead, which is
known to the State of California to cause cancer, birth defects or reproductive harm.
For more information go to www.P65Warnings.ca.gov.
WARNING:
Drilling, sawing, sanding or machining wood products can expose
you to wood dust, a substance known to the State of California to cause cancer.
Avoid inhaling wood dust or use a dust mask or other safeguards for personal
protection. For more information go to www.P65Warnings.ca.gov/wood.
WARRANTY
DK SERIES FULLY AUTOMATIC POCKET HOLE MACHINES
Do not return the machine to the dealer for warranty service.
For all warranty issues, contact Kreg Tool Company Customer
Service at the address or phone number below.
Kreg Tool Company warrants to authorized distributors of
Kreg products and original purchasers from such distributors,
the DK5100 pocket-hole machine to be free from defects in
materials and workmanship for a five-year period from the date
of delivery to the original purchaser. The motors and other
working parts of the machine carry a one (1) year warranty
from the date of delivery to the original purchaser. The drill
guides carry a lifetime warranty. Kreg, at its option, will repair
or replace any product or component part thereof proving
defective during the warranty period.
This warranty only applies to products used in accordance with
all instructions set forth in catalogs and manuals furnished by
Kreg Tool Company as to operation, maintenance and safety.
This warranty does not apply to (1) items normally consumed
or requiring replacement due to normal wear (drill bits, lubricants,
etc.); (2) the cost of removal of components if such removal is
authorized by Kreg Tool Company; (3) shipment to Kreg Tool
Company's repair facility; or (4) reinstallation of components.
GENERAL SAFETY INSTRUCTIONS
Extension Cord Length
50'
75'
100'
150'
Recommended Wire Gauge
16
16
14
12
16
14
12
10
14
12
10
NR
12
NR
NR
NR
This warranty becomes effective only when the accompanying
card or online form (available at www.kregtool.com) is fully and
properly completed and returned to Kreg Tool Company within
ten (10) days from date of delivery to the original purchaser.
This warranty is null and void if the product has been subjected
to (1) misuse, abuse, or improper service or storage; (2) accident,
neglect, damage, or other circumstances beyond Kreg Tool
Company control; and (3) modifications, disassembly, tampering,
alterations, or repairs outside of the Kreg Tool Company factory not
authorized by Kreg Tool Company. This warranty does not apply
to (1) any product not bearing the original serial-number plate; (2)
non-original purchasers; and (3) normal wear and tear, corrosion,
abrasion, or repairs required due to natural causes or acts of God.
To obtain warranty service, contact the distributor from whom
the pocket-hole machine was purchased or contact Kreg Tool
Company directly. Proof of purchase is required for remedy
under the terms of this warranty. Kreg Tool Company assumes
no responsibility for products returned without prior authorization.
Kreg Tool Company obligations under this warranty shall be
exclusively limited to repairing or replacing (at Kreg Tool Company
200'
option) products determined by Kreg Tool Company to be defective
upon delivery to the Kreg Tool Company factory and inspection by
12
Kreg Tool Company technicians. Under no circumstance shall Kreg
Tool Company be liable for incidental or consequential damages
NR
resulting from defective products, nor shall Kreg Tool Company
NR
liability exceed the purchase price paid by the original purchaser.
NR
This is the Kreg Tool Company sole warranty. Any and all
other warranties implied by law, including any warranties for
merchantability or fitness for a particular purpose, are hereby
limited to the duration of this warranty. Kreg Tool Company shall
not be liable for any loss, damage, or expense directly or indirectly
related to the use of its products or from any other cause or for
consequential damages including without limitation, loss of time,
inconvenience, and loss of production. The warranty contained
herein may not be modified and no other warranty, expressed or
implied, shall be made by or on behalf of Kreg Tool Company.
Register your warranty within ten (10) days of date of delivery.
Warranty service will not be provided without registration.
Keep a copy of this form for your records.
For your records the following information will be useful in the
event warranty service is required. For a complete record,
attach a copy of the purchase invoice to this form.
Date of Purchase: ___/___/_____
Purchased From: __________________________________
Serial Number: ____________________________________
(serial number located on front edge of work surface plate)
Publicidad
Tabla de contenido
