Braun BC10-DCF Instrucciones Para El Usuario página 2

English
Battery precautions
1. Do not use rechargeable batteries.
2. Use only alkaline AA batteries of the same or equivalent type.
3. Insert batteries with the correct polarity.
4. Keep batteries away from children.
5. Dispose of exhausted batteries according to local legal
requirements. Do not dispose them by throwing away with
normal household rubbish.
6. Avoid short circuiting the contacts in the battery compartment
and battery terminals.
7. Remove batteries from the unit if it will not be used for long
period of time.
8. Exhausted batteries should be removed from the battery
compartment to prevent over-discharge, which can cause
leakage and may cause damage to the clock.
Getting started
1. Remove the battery door.
2. Insert 2xAA size new batteries (use good branded alkaline
batteries) as indicated in the battery compartment, and press the
"reset" key to reset the clock. The display will turn on after a few
seconds.
3. After 6 seconds, the Clock will automatically start scanning for
the radio controlled time signal.
4. Close the battery door.
Radio controlled operation DCF version
(Germany & European countries)
This Braun digital alarm clock is set and controlled automatically
by DCF radio signal. The DCF radio time code signal is broadcast
from Frankfurt, Germany. The coverage of the DCF signal is the
whole of Germany. The time code signal can be received up to
1500km from Frankfurt. This covers most of Central and Western
Europe.
Important
For best reception performance, please read the following in-
structions.
1. We strongly recommend you start your clock at night. Allow the
clock to receive the signal automatically overnight.
2. Place the unit away from interfering sources such as TV set,
computers, microwaves, etc.
3. Avoid placing the unit on or next to metal surfaces.
4. Avoid closed areas such as airports, basements, cement office
buildings or factories.
Function keys
TIME SETTING / NEUTRAL / ALARM SETTING switch
- Slide the switch to the TIME SETTING position to set the clock
time.
- Slide the switch to the ALARM SETTING position to set the alarm
time.
- Slide the switch to the NEUTRAL position to exit the setting
mode and return to normal display.
+ Key
- When the setting switch is in the NEUTRAL position, press the +
key to change between 12 and 24 hour display format.
- In TIME SETTING or ALARM SETTING mode press to increase the
setting value. Press and hold to speed up the setting.
- Key
- When the setting switch is in the NEUTRAL position, press the -
key to change the temperature display between °C and °F format.
- In TIME SETTING or ALARM SETTING mode press to decrease
the setting value. Press and hold to speed up the setting.
ALARM ON / OFF slider
- Shift the ALARM ON / OFF slider up to enable the alarm.
- Shift the ALARM ON / OFF slider down to disable the alarm.
SNOOZE / LIGHT touch button
- Tap to turn on the backlight for 10 seconds.
- Tap to stop the alarm and activate the 5 minute snooze function.
RESET key
- Press by using a pin to reset all values to default. In case of a
malfunction, the unit has to be reset.
RCC key
- Press to receive the RC signal in order to test the reception.
- Press and hold the RCC key for over 3 seconds until "OFF" is
displayed to disable the automatic RC function.
CALENDAR SETTING button
- Press CALENDAR SETTING button to set year/month/date.
BACKLIGHT ON /OFF switch
- Slide the switch to ON position to enable the night light mode.
- Slide the switch to OFF position to disable the night light mode.
Product description (Image 1)
1. LCD display
2. SNOOZE / LIGHT touch button
3. ALARM ON / OFF slider
4. TIME SETTING / NEUTRAL / ALARM SETTING switch
5. + Key
6. - Key
7. Battery compartment
8. RESET key
9. RCC key
10. CALENDAR SETTING button
11. BACKLIGHT ON / OFF switch
12. Light sensor
Display details (Image 2)
A. Time
B. AM / PM indicator (for 12 hour format)
C. Alarm time
D. Alarm icon
E. DST indicator
F. RC signal strength indicator
G. Temperature
H. Month
I. Date
J. Low battery indicator
RC signal strength indicator (Image 3.)
The signal indicator displays signal strength in 3 levels. Wave seg-
ment flashing means the time signals are being received. Press
and hold the RCC key for over 3 seconds until "OFF" is displayed to
disable the automatic RC function.
Note: You may use the RCC key to receive the time signal manual-
ly. The receive mode stops automatically after 6 minutes.
Setting the time
1. Slide the TIME SETTING / NEUTRAL / ALARM SETTING switch to
the TIME SETTING position.
2. Press the '+' or '-' key to set the desired value. Press and hold the
'+' or '-' key to speed up the setting.
3. Slide the TIME SETTING / NEUTRAL / ALARM SETTING switch to
the NEUTRAL position to return the normal display and save the
settings.
Setting the year, date and month
1. Press the CALENDAR button.
2. Press the '+' or '-' key to set the current year. Press and hold the
'+' or '-' key to speed up the setting. Press the CALENDAR button
to save this setting.
3. Press the '+' or '-' key to set the current month. Press and hold
the '+' or '-' key to speed up the setting. Press the CALENDAR
button to save this setting.
4. Press the '+' or '-' key to set the current date. Press and hold the
'+' or '-' key to speed up the setting. Press the CALENDAR button
to save this setting and exit the CALENDAR mode.