Publicidad
be used to develop cornering or screw joints. The
areas of use are carrying out repair and construction,
carpentry and other work-related self-amateur activity
.. Not permitted the use of power tools for activities
other than its intended purpose.
7. Information on noise and vibration emitted
The values are measured according to EN
60745. A level of noise generated is generally: the
sound pressure level 98 dB (A); sound power 109
dB (A). Uncertainty K = 3 dB. Work with a silencer!
The resultant value of vibration (the vector sum of
the three directions) is determined according to EN
60745: Drilling in metal: the value of the emitted
vibrations a
= 4,7 m/s
h
s
, hammer drilling in concrete: value the emitted
2
vibrations a
= 24,2 m/s
h
cornering / development: the value of the emitted
vibrations ah <2,5 m/s
That in this operating manual for the vibration value is
measured by the method specified in EN 60745 and
can be used to compare different power. The level
of vibration varies depending on the specific activity
carried out and in some cases may exceed that
amount in that direction. If power is used for a long
time in this mode, the load caused by vibration, could
be underestimated. Directions: For an exact estimate
of the burden of vibrations in a working cycle should
be recorded and the intervals in which the power is off
or idling. This can significantly reduce the reporting
burden of vibrations throughout the business cycle.
8. Preparing for the job. Installation of accessories
and auxiliary tools.
8.1.1. Auxiliary handle.
Use only the impact drill fitted with an auxiliary
handle (8). You can insert auxiliary handle (8) in
practically any position, to ensure your comfortable
and safe position for the job. Turn the handle itself
(8) axis and counterclockwise, thus reducing the
firmness of the loop around the head of the drill and
you can rotate the handle vspomagatelnata in the
desired position. Then tighten the grip again (8), such
as turning it clockwise.
8.2. Setting the depth of drilling. With deep baffle
(5) can be pre-set depth of drilling. Pull the baffle so
deep that the distance along the axis between the
tip of the drill and deep baffle is equal to the desired
depth of the hole.
8.3. Placing the drill in the chuck. Turn off the
power of power. Put the key in one of the open side
of the chuck. Dissolving the jaws to the desired
size and place in the drill chuck. With key-locking in
three successive drill a hole in the chuck. We must
always remember that the key should be removed
, uncertainty K = 1,5 m/
2
, uncertainty K = 1,5 m/s
2
, uncertainty K = 1,5 m/s
2
from the drill after the completion of operations
related to installation and dismantling of the drill.
When mounting a new drill should be checked by the
inclusion of a short drill, drill that rotates in an axis
without "flicker". This will help us make sure that it is
not distorted.
8.4. Inclusion and exclusion. Beware of the
voltage of supply network! Supply voltage of the
network must conform to the details shown on the
plate of power. Appliances marked with 230 V, can be
supplied with a voltage of 220 V.
8.5. To turn the drill press and hold the trigger
switch (1). For locking of the starting switch pressed
(1) press (3). Exclusion relax power trigger switch (1),
respectively, if anchored to the button (3), first press
the short term and then release the trigger switch (1).
,
8.6. Adjust the speed of rotation. Drill allows to
2
work with different speed of spindle. Alignment is done
.
using the position (2). In the range of each setting
2
a speed can be adjusted smoothly by increasing
speed and reducing pressure on the trigger button
(1). Zavarteneto right speed regulator (2) leads to
increase their rotation and left to decrease.
8.7. Correct choice of the rate of speed shall be
held where drill is included without load. So speed-
minded when working with a load may be lower.
8.8. Hammer drilling.
Place the switch (6) the symbol "hammer drilling."
Switch (6) falls in the correct position with a distinct
twinge.
8.9. Tools to develop or cornering.
Turntable working instrument can be bent. After
continuous operation with low-speed power to cool
as to leave it idling for approximately 3 minutes with
a maximum speed of rotation. When working with
terminals must always use a universal extension. Use
only the cores that are suitable for heads of screws.
Turning to always place the switch "drilling / hammer
drilling» (6) in position «Drilling».
8.10. Select the direction of rotation. With the
switch (4) you can change the direction of rotation
of power. Rotate right: For drilling and turning the
screw press to switch the direction of rotation (4)
at point blank range left. Rotate left: To develop the
screws and nuts, press switch direction of rotation (4)
right to the point blank range. Switch (6) the choice
of operation should be in position «Drilling». It must
be done to change the direction of rotation when the
spindle rotates a drill!
8.11. Not used in rotation to the left mode of attack.
8.12. When you need to vent large diameter, is
recommended first to break a small opening, which
will then be drilling to the desired size. This will
prevent overloading the drill. Drilling deep holes
13
Publicidad
