Krups GN9031 Manual Del Usuario página 14

EN
Choose one of the following drums depending on the type of food and the desired result:
Drum c8: Slices: potatoes, red beetroot, carrots, cucumber, cabbage / Drum c9: Grates coarsely:
potatoes, red beetroot, carrots, cheese / Drum c10: Grates finely: cheese, carrots / Drum c11: Grinds: dry
foods (almonds, walnuts, hazelnuts, parmesan); Makes into strands: potatoes / Drum c12: Crushes: ice
Clip the adaptor (c1) onto the drum holder (c2) and insert the chosen drum into the drum receptacle turning
slightly so that it lodges correctly into its housing. Then position the drum locking ring (c4) (fig. 17).
Insert the base on the runners located on each side of the adaptor (c1) then the drum holder (c2) (fig. 18).
Do not clip on the base (c5) from below (fig. 19).
Position your mixer vertically then insert the adaptor (c1) into the corresponding holes turning slightly until
it locks completely (fig. 20).
Place the 2.5 l container under the vegetable cutter to collect the food (fig. 21).
Connect the appliance to the mains socket.
3.2 U
se
Place the food into the feeder tude, guiding them using the pusher (c3) (fig. 21).
Set the button to maximum speed.
3.3 D
isassembly
Disconnect the appliance.
To disassemble the drum holder (c2), press the button (c6) located at the front of the adaptor and remove
the feeder tube (fig. 22).
Press the button (c7) at the rear to release the adaptor (c1) from the mixer (fig. 23).
Remove the base (c5) by sliding it along the runners located at each side of the adaptor (c1) then the drum
holder (c2).
3.4 C
leaning
The drum holder (c2), drums (c8 c9 c10 c11 c12), drum locking ring (c4) and the pusher (c3) are dis-
hwasher safe.
The mixer and the adaptor must be washed with a damp cloth.
Note:
- Always use a the pusher (c3) to guide the food into the feeder tube, never your fingers, nor a fork,
spoon, knife or any other object.
- When putting away your vegetable cutter, you can slide the base over the feeder tube. (fig. 24).
4 -
BLENDER ATTACHMENT ACCESSORY: mix, emulsify (depending on model)
4.1 A
ssembly
To insert the blender attachment (d1), open the rear hatch (a5) (fig. 8).
Insert the blender attachment and screw tightly (fig. 25).
Connect the appliance.
4.2 U
se
Depending on the type of preparation, place the ingredients in the container provided (1 l bowl (e) or 2.5
l bowl (f) (depending on the model) or in a suitable container (bowl or beaker, preferably deep).
When you blend directly in a container, remove the container from the heat source when mixing hot prepa-
rations.
The food must cover at least the lower part of the blender attachment to guarantee effective functioning.
The container must be filled to the maximum or two-thirds full to prevent spilling.
To start, press the 'whisk ejection' button (a4) (fig. 27).
Release the button (a4) before removing the blender attachment (d1) from the preparation to prevent
splashes.
Practical advice:
- Never operate the blender attachment when empty.
- For fruit preparations, chop and deseed/destone the fruit first.
- Do not use the blender attachment with hard food such as ice, sugar, coffee grains, cereals and chocolate.
4.3 D
isassembly
Disconnect the appliance.
Unscrew the blender attachment (fig. 28).
4.4 C
leaning
The blender attachment can be washed in the dishwasher, in the lower basket with blades facing upwards
(take care as the blades are extremely sharp) (fig. 29).
5 - 150 ml Mini Chopper (E) (available as an additional accessory)
5.1 Assembly
Place the blade unit (g2) on bowl (g1) (fig. 30).
14