Publicidad
Idiomas disponibles
Idiomas disponibles
Read instructions carefully before assembling or installing your
fan. It is important that you observe all safety information to
help prevent personal injury and/or property damage.
1.Installation work and electrical wiring should be done by
qualified person only in accordance with all applicable codes and
standards.
2.All wiring and installation procedures must satisfy National
Electrical Codes (ANSI/ NFPA 70) and Local Codes.
3.Disconnect the fan from the power supply before any servicing.
4.Use this fan only in the manner intended by the manufacturer.
This fan is intended for permanent installation and to be used for
circulation only.
5.The secondary support cable included with the fan must be
properly connected.
6.To reduce the risk of personal injury, do not bend the blade mount
when installing the mount onto the motor, installing the blades
onto the mount, or cleaning the fan.
7.Before servicing or cleaning unit, switch power off at service panel
and lock service panel disconnecting means to prevent power
from being switched on accidentally. When the service
disconnecting means cannot be locked, securely fasten a
warning device, such as a tag, to the service panel.
8.Be careful of the fan and blades when cleaning, painting, or
working near the fan. Always turn off the power to the ceiling fan
before servicing.
9.Do not insert foreign objects in between rotating fan blades.
10.Ceiling fans without guards are to be installed at least 10 feet
above the floor with adequate clearance between blades and
adjacent walls, furnishings, etc.
11.When mounted in cathedral ceiling, blade tips should be at least
1 foot from the angled roof line or air turbulence may cause the
fan to sway.
12.The supporting beam must be capable of holding at least 90
pounds (or the weight of the fan plus any accessories that might
be added).
Suitable for Commercial or Industrial Use Only.
Model
Size(inch)
Voltage(V)
Frequency(Hz)
Wattage(W)
AMPS(A)
RPM
Airflow(CFM)
Downrod Dimensions(inch)
Blade Pitch
Speeds
Net Weight(lbs)
Certification
Industrial DC Ceiling Fan
GENERAL SAFETY INSTRUCTIONS
φ1-
13.For supply connections, if the conductor of a fan is identified
as a grounded conductor, then it should be connected to a
grounded conductor power supply. If the conductor of a fan is
identified as an ungrounded conductor, then it should be
connected to an ungrounded conductor power supply. If the
conductor of a fan is identified for equipment grounding, then
it should be connected to an equipment grounding conductor.
14.To reduce the risk of fire or electric shock, do not use this fan
with other types of solid-state speed control devices.
TO REDUCE THE RISK OF SHOCK, THIS FAN
MUST BE INSTALLED WITH A GENERAL USE
ISOLATING WALL CONTROL/SWITCH.
To reduce the risk of personal injury, do not bend
the blade bracket (flange or blade holder) when
installing the brackets, balancing the blades, or
cleaning the fan. Do Not Insert Foreign Objects In
Chemical Burn Hazard. Keep batteries away from
children.
This product contains a lithium button/coin cell
battery. If a new or used lithium button/coin cell
battery is swallowed or enters the body, it can cause
severe internal burns and can lead to death in as
little as 2 hours. Always completely secure the
battery compartment. If the battery compartment
does not close securely, stop using the product,
remove the batteries, and keep it away from children.
If you think batteries might have been swallowed or
placed inside any part of the body, seek immediate
medical attention.
-The cells shall be disposed of properly, including
keeping them away from children.
-Even used cells may cause injury.
SPECIFICATION
293047
293048
72
120
60
47.5
0.68
145
11,290
φ1-
1/ 32
x10"
4°
6
21.6
UL,cUL
UL,cUL
2
Between Rotating Fan Blades.
293049
96
120
60
47.5
0.68
92
17,018
19,448
φ1-
1/ 32
x10"
4°
6
24.7
UL,cUL
User's Manual
108
120
60
48
0.7
81
1/ 32
x10"
4°
6
25.6
Publicidad
