Publicidad
Idiomas disponibles
Idiomas disponibles
t
RoUbLE
Be CERTAIN to shut off the welder, disconnect it from power, and discharge to ground before
adjusting, cleaning, or repairing the unit.
NO ARC
FLYING SPATTER
NO SHIELDING GAS
POROSITY IN METAL
REPLACEMENT PARTS
MODEL NO
DESCRIPTION
2-1470
DRIVE ROLLER .023/.030
2-1471
DRIVE ROLLER .030/.035
2-1473
DRIVE ROLLER THREADED KNOB
2-1474
REPLACEMENT GAS HOSE
2-1475
OEM REGULATOR
2-1476
MAIN PCB
2-1477
FRONT PANEL PCB
2-1478
CONTROL PCB
2-1480
MALE MACHINE PLUG
2-1481
REPLACEMENT GAS DIFFUSER
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR
DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT THEY ARE QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT
THEY ARE QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS
REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS, AND NOT THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT
OF THEIR REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF THEIR INSTALLATION OF REPLACMENT PARTS THERETO.
! WARNING: Electric Shock Can Kill. Do not touch electrical live parts or electrodes with skin or wet clothing. Always wear dry insulated gloves. Insulate yourself from work and ground.
Fumes and gases can injure you. Keep your head out of fumes. Use enough ventilation and/or exhaust at the arc to keep fumes and gases from your breathing area. Welding sparks can
cause fire or explosion. Keep flammable material away. Keep fire extinguisher nearby when welding. Arc rays can injure eyes and burn skin. Wear correct eye and body protection.
S
hootiNg
1. Ground cable not connected properly
2. Worn, dirty, or incorrect size contact tip
1. Work piece is too dirty, greasy, or rusty
1. Torch is not connected properly
2. Gas hose is blocked or kinked
3. Interior rubber gas hose disconnected
1. Shielding gas cylinder is empty
2. Insufficient or excess shielding gas
3. Work piece is dirty
4. Incorrect polarity
5. Contaminated or dirty wire
e
ect
l
®
www.ktindustries.net
PAGE | PAGE | PÁGINA
1. Reconnect ground cable
2. Replace or clean contact tip
1. Clean work piece
1. Reconnect torch
2. Check gas system and gas line
3. Connect gas hose and ensure firm connection
1. Check cylinder and refill if necessary
2. Check regulator for proper flow
3. Clean work piece
4. Ensure correct polarity for operation. DCEP for MIG,
DCEN for Flux Cored
5. Ensure wire is clean and free of rust, replace if necessary
MODEL NO
DESCRIPTION
2-1482
SWAN NECK TORCH W/ DIFFUSER
2-1483
MIG TORCH REPLACEMENT TRIGGER ASSEMBLY
2-1484
MIG TORCH HANDLE PLASTIC KNOB
2-1485
MIG TORCH PLASTIC HANDLE
2-1486
COMPLETE MIG TORCH HANDLE/LEAD
2-1488
DOOR ASSEMBLY W/ HINGE, KNOB, SCREWS
2-1489
TOP HANDLE ASSEMBLY
2-1522
FLUX CORE NOZZLE
2-1580
SPOOL ADAPTOR KIT (INCLUDES NUT & SPRING)
2-1581
POWER CORD ADAPTOR
K-T Industries, Inc.
3112 NW Blvd.
Sheldon, IA 51201
12
®
®
®
®
Publicidad
