Publicidad
Idiomas disponibles
Idiomas disponibles
Moving the Locker on an Incline or
Rough Surface
Take care that the locker does not tip or become
unbalanced when moving it on an incline or rough
surface. Do not exceed an incline of 10 degrees.
Lock the locker and secure all items before moving.
Rolling the Locker
The locker is only intended for rolling short distances.
Do not modify the locker in any way. Drilling holes
or modifying the locker will lower the load capacity,
which can cause the locker to collapse, resulting in
injury. Lock the locker and secure all items before
rolling.
Lifting the Locker
The locker is not intended to be lifted. However, if
you need to lift, empty the locker and then place
straps or forks inside and next to casters. Do not lift
loaded lockers. Never lift by the side handle. Be sure
all bystanders are moved away before lifting locker.
MAINTENANCE
To reduce the risk of injury, contact
WARNING
MILWAUKEE Corporate After Sales
Service Technical Support for ALL repairs and
replacement parts.
Maintaining the Locker
Keep your locker in good repair by adopting a regular
maintenance program. Before use, examine the gen-
eral condition of your locker. Check for loose screws,
misalignment, binding of wheels, broken parts and
Do not use a damaged locker.
Maintaining the Casters
Grease the casters annually using high quality bear-
ing grease.
Cleaning
This steel locker has been coated with industrial
cals (oil, grease or other chemical) to remain on the
powder coating surface. Use a glass cleaner to clean
and maintain all surfaces of powder coating.
Keep the locker handles and wheels clean, dry and
free of oil or grease. Use only mild soap and a damp
cloth to clean your locker since certain cleaning
agents and solvents are harmful to plastics. Some of
these include: gasoline, turpentine, lacquer thinner,
chlorinated cleaning solvents, ammonia and house-
hold detergents containing ammonia. Never use
For service and repair information, including the or-
dering of service parts, call our Corporate After Sales
Service Technical Support line at 1-800-SAWDUST,
or visit our website at www.milwaukeetool.com.
Grease
Points
Service
WIRELESS COMMUNICATION
Pursuant to part 15.21 of the FCC Rules, you are cau-
approved by the party responsible for compliance
could void your authority to operate the product.
NOTE: This equipment has been tested and found
to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection
against harmful interference in a residential instal-
lation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may
XXI
1 : 2
cause harmful interference to radio communications.
However, there is no guarantee that interference will
not occur in a particular installation. If this equipment
does cause harmful interference to radio or televi-
sion reception, which can be determined by turning
try to correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and
receiver.
• Connect the equipment into an outlet on a circuit
• Consult the dealer or an experienced radio/TV
technician for help.
This device complies with part 15 of the FCC Rules
and ISED-Canada's license exempt RSS standards.
Operation is subject to the following two conditions:
1) This device may not cause harmful interference,
and 2) This device must accept any interference
received, including interference that may cause
undesired operation.
ACCESSORIES
Modifying the locker to accept
WARNING
other accessories may be hazard-
ous, resulting in injury or property damage. Use
cording to the manufacturer's instructions.
For a complete listing of accessories, go online to
www.milwaukeetool.com or contact a distributor.
SERVICE - UNITED STATES
1-800-SAWDUST
Monday-Friday, 7:00 AM - 6:30 PM CST
www.milwaukeetool.com
or visit
Contact Corporate After Sales Service Technical
-
Support with technical, service/repair, or warranty
questions.
Email: metproductsupport@milwaukeetool.com
B e c o m e a H e a v y D u t y C l u b M e m b e r a t
www.milwaukeetool.com to receive important
SERVICE - CANADA
Milwaukee Tool (Canada) Ltd
1.800.268.4015
Monday-Friday, 7:00 AM - 4:30 PM CST
or visit www.milwaukeetool.ca
7
-
(1.800.729.3878)
Publicidad
