Publicidad
IMPORTANT
Please read
these instructions carefully before you start to assemble this
product
.
Please
carry
out the
steps
in
the order
set
out
in
these instructions.
Keep
these instructions
in
a
safe
place for
future
reference.
Safety Advice
For
safety purposes we
strongly recommend the product to
be
assembled by at least
two
people.
Some parts may have sharp edges.
Please be
careful when handling components. Always wear
gloves,
eye
protection,
and long
sleeves
when assembling or performing any maintenance on your
product.
Do
not attempt to
assemble the
product
in
windy or wet conditions.
Do
not attempt to
assemble the
product if you
are
tired,
have
taken drugs,
medications or alcohol, or if you
are
prone to dizzy
spells.
Dispose
of
all
plastic
bags safely
-
keep
them
away
from children's
reach.
Keep
children away from the assembly
area.
When using
a
stepladder or power
tools, make
sure
that you
are
following
the manufacturer's safety advice.
Keep
roof and gutters
clear
of
snow,
dirt
& leaves.
Heavy
snow load on the roof
can make
it unsafe to stand below or nearby.
Do
not
lean
against or push the product during construction.
Hot items
such
as
recently
used grills,
blowtorches
etc.
must not
be
stored inside the product.
Heavy or sharp articles should
not
be
leaned against the wall panels.
Make Sure
there
are no
hidden pipes or cables
in
the ground before inserting the
pegs
(not supplied)
Do
not touch overhead power
cables
with
the aluminum profiles.
If
color
was
scratched
during
assembly it can be fixed.
Note:This product must
be
anchored
on
to
a
leveled surface and solid
foundation to
ensure its
stability.
Make sure
that
screws
and anchors
are
compatible with foundation type.
Make sure
that
there
are no
obstructions between the assembly
area
and the final position.
Cleaning Instructions
In
order to
clean
the product,
use
a
mild detergent solution
and rinse
with
cold clean water.
Do
not
use
acetone, abrasive cleaners, or
other
special
detergents to
clean
the
panels.
Clean
the product once assembly
is
complete.
Before Assembly
Choose
your
site
carefully before beginning
assembly.
The
ground
surface must
be
perfectly flat
and leveled and have
a
solid
base such
as
concrete, asphalt,
deck
etc.
Parts
should
be
laid
out
close at hand. Keep all small parts (screws etc.) in
a
bowl
so
they do not get
lost.
Please
consult your
local
authorities if any permits
are
required prior to constructing the product.
Make sure you received
all boxes
according to the additional page (Extending your SunRoom) on the
instruction
manual.
As
soon
as
you
are
ready
to
assemble
your product
(you can start
with this
box),
sort the parts and check against the
content
parts
list.
Complete
site
preparation before unpacking parts and beginning
assembly.
During Assembly
When
encountering the information
icon,
please refer
to the relevant assembly
step
for additional comments and
assistance.
This icon
indicates
that the installer should
be
inside the product.
During assembly
use
a
soft surface below the parts to avoid scratches and
damages.
Steps
Steps 5+6:
If
you
have
purchased
Sun
Room
8',
you should
use
the entire 7802 panel.
If
you
have
purchased
Sun
Room
6',
you should cut
panel 7802 to
size, in
accordance with
illustration
6a.
Step
7:
Please
decide your preferred
window
location. Available options
are
shown
in
the
illustration.
Step 17:
If
the
window
doesn't
close
properly,
please release
the
screws,
adjust the profile
and
re-tighten the
screws.
* Please
tighten
all screws
when completing assembly.
Publicidad
