Safety Regulations - EINHELL Expert TE-TS 1825/1 U Manual De Instrucciones

Anleitung_TE_TS_1825_U_SPK8_- 26.09.12 15:19 Seite 29
Important!
When using the equipment, a few safety precautions
must be observed to avoid injuries and damage.
Please read the complete operating instructions and
safety regulations with due care. Keep this manual in
a safe place, so that the information is available at all
times. If you give the equipment to any other person,
hand over these operating instructions and safety
regulations as well. We cannot accept any liability for
damage or accidents which arise due to a failure to
follow these instructions and the safety instructions.

1. Safety regulations

CAUTION!
Read all safety regulations and instructions.
Any errors made in following the safety regulations
and instructions may result in an electric shock, fire
and/or serious injury.
Keep all safety regulations and instructions in a
safe place for future use.
Important. The following basic safety actions
must be taken when using electric tools in order
to protect the user from electric shocks and the
risk of injury and fire. Read and follow these
instructions before using the equipment.
1. Keep your work area tidy
- Untidy work areas can result in accidents.
2. Make allowance for ambient conditions
- Do not expose electric tools to rain. Never use
electric tools in damp or wet locations. Provide
good lighting. Do not use electric tools near
flammable liquids or gases.
3. Guard against electric shock
- Avoid bodily contact with earthed parts (e.g.
pipes, radiators, cookers and refrigerators).
4. Keep children away
- Do not allow other persons to touch the tool or
cable, keep them away from your work area.
5. Keep your electric tools in a safe place.
- Unused tools should be stored in a dry, locked
room out of children's reach.
6. Do not overload your tools
- Tools work better and safer when used within
their quoted capacity range.
7. Use the right tool.
- Do not use tools or attachments too weak for
heavy duty work. Never use tools on jobs for
which they are not intended; for example, do not
use a hand-held circular saw to fell trees or lop off
branches.
8. Wear suitable work clothes
- Do not wear loose clothing or jewelry. They can
be caught in moving parts. Rubber gloves and
nonskid footwear are recommended when
working outdoors. Wear protective nair covering
to contain long hair.
9. Wear safety goggles.
- Use a dust mask when working on dusty jobs.
10. Do not use the cable for purposes other than
that for which it is designed.
- Do not carry the tool by its cable and do not use
the cable to pull the plug out of the socket.
Protect the cable from heat, oil and sharp edges.
11. Secure your workpiece
- Use clamps or a vise to hold the workpiece
securely. This is safer than using your hand and
also enables you to operate the machine with
both hands.
12. Do not overstretch.
- Avoid abnormal working postures. Make sure
you stand squarely and keep your balance at all
times.
13. Take care of your tools
- Keep your tools sharp and clean in order to work
well and safely. Follow the maintenance
regulations and the instructions for changing
tools. Check the power plug and cable on a
regular basis and have them replaced by an
authorized specialist if they are damaged. Check
the extension cable regularly and replace it if
damaged. Keep handles dry and free from oil and
grease.
14. Pull the power plug
- When tools are not in use, before starting any
maintenance work or when changing attachments
such as saw blades, drill bits and all kinds of
mounted tools.
15. Always remove keys and wrenches after use
- Before switching on, make sure that all keys and
wrenches have been removed from the
equipment.
16. Avoid unintentional starting
- Never carry a tool with your finger on the switch
button while the tool is connected to the power
supply. Make sure that the switch is turned off
when connecting the tool to the power supply.
17. Extension cables out of doors
- Use only authorized and accordingly labeled
extension cables out of doors.
18. Be alert at all times
- Keep an eye on your work. Use common sense
when working. Never use the tool when you are
distracted.
19. Check the equipment for damage
- Before using the tool again, check the safety
devices or any slightly damaged parts to ensure
that they are in good working order. Check that
GB
29