Technical Data - EINHELL Expert TE-TS 1825/1 U Manual De Instrucciones

Anleitung_TE_TS_1825_U_SPK8_- 26.09.12 15:19 Seite 33
result from such misuse. The machine is to be
operated only with suitable saw blades (saw blades
made of HM or CV) It is prohibited to use any type of
HSS saw blade and cutting-off wheel. To use the
machine properly you must also observe the safety
regulations, the assembly instructions and the
operating instructions to be found in this manual.
All persons who use and service the machine have
to be acquainted with this manual and must be
informed about the machineʼs potential hazards.
It is also imperative to observe the accident
prevention regulations in force in your area.
The same applies for the general rules of
occupational health and safety.
The machine is to be used only for its prescribed
purpose. Any other use is deemed to be a case of
misuse. The user / operator and not the
manufacturer will be liable for any damage or injuries
of any kind caused as a result of this.
Please note that our equipment has not been
designed for use in commercial, trade or industrial
applications. Our warranty will be voided if the
machine is used in commercial, trade or industrial
businesses or for equivalent purposes.
The manufacturer shall not be liable for any changes
made to the machine nor for any damage resulting
from such changes.
Even when the machine is used as prescribed it is
still impossible to eliminate certain residual risk
factors. The following hazards may arise in
connection with the machineʼs construction and
design:
Contact with the saw blade in the uncovered
n
saw zone.
Reaching into the running saw blade (cut
n
injuries).
Kick-back of workpieces and parts of work-
n
pieces.
Saw blade fracturing.
n
Catapulting of faulty carbide tips from the saw
n
blade.
Damage to hearing if ear-muffs are not used as
n
necessary.
Harmful emissions of wood dust when used in
n
closed rooms.

5. Technical data

AC motor
Power P S1 1500 W S6 40% 1800 W
Idle speed n
0
Cutting-off wheel Ø 250 x Ø 30 x 2.4 mm
Number of teeth
Table size
Table width extension, left/right
Table length extension, rear
Cutting height max.
Height adjustment
Tilting saw blade
Extractor socket
Sound and vibration
Sound and vibration values were measured in
accordance with EN 61029.
Idle
Sound pressure level LPA 104,5 dB(A)
K uncertainty
pA
Sound power level LWA 114,1 dB(A) 105,2 dB(A)
K uncertainty
WA
The quoted values are emission values and not
necessarily reliable workplace values. Although there
is a correlation between emission and immission
levels it is impossible to draw any certain conclusions
as to the need for additional precautions. Factors
with a potential influence on the actual immission
level at the workplace include the duration of impact,
the type of room, and other sources of noise etc.,
e.g. the number of machines and other neighboring
operations. Reliable workplace values may also vary
from country to country. With this information the
user should at least be able to make a better
assessment of the dangers and risks involved.
Wear ear-muffs.
The impact of noise can cause damage to hearing.
„Keep the noise emissions and vibrations to a
minimum.
Only use appliances which are in perfect working
n
order.
Service and clean the appliance regularly.
n
Adapt your working style to suit the appliance.
n
Do not overload the appliance.
n
GB
230V 50Hz
5700 min -1
24
625 x 440 mm
625 x 250 mm
400 x 440 mm
73 mm/90°
53 mm / 45°
infinite 0 -73 mm
infinite 0° - 45°
Ø 36 mm
mode
95,5 dB(A)
3 dB
3 dB
33