Publicidad
Idiomas disponibles
Idiomas disponibles
LAWN
MOWER
Always observe safety rules when per-
forming any maintenance.
TIRES
, Keep tires free of gasoline,
oil, or insect
control chemicals which can harm rubber.
, Avoid stumps, stones, deep ruts, sharp
objects and other hazards that may
cause tire damage.
DRIVE WHEELS
Check front drive wheels each time before
you mow to be sure they move freely.
The wheels not turning freely means trash,
grass cuttings, etc. are in the drive wheel area
and must be cleaned to free drive wheels.
If necessary to clean the drive wheels, be
sure to clean both front wheels.
1. Remove hubcaps, Iocknuts & washers.
2.
Remove wheels from wheel adjusters.
3.
Remove any trash or grass cuttings
from inside the dust cover, pinion and/
or drive wheel gear teeth.
4.
Put wheels back in place.
NOTE:
If after cleaning, the drive wheels
do not turn freely, contact a Sears or other
qualified service center.
BLADE CARE
For best results, mower blade must be kept
sharp.
Replace a bent or damaged blade.
A CAUTION"
Use only a replacement
blade approved by the manufacturer
of
your mower. Using a blade not approved
by the manufacturer
of your mower is haz-
ardous, could damage your mower and
void your warranty.
TO REMOVE
BLADE
1. Disconnect
spark plug wire from spark
plug and place wire where it cannot
come in contact with plug.
2. Turn lawn mower on its side. Make
sure air filter and carburetor are up.
3. Use a wood block between blade and
mower housing to prevent blade from
turning when removing blade bolt.
NOTE:
Protect your hands with gloves
and/or wrap blade with heavy cloth.
4.
Remove blade bolt by turning counter-
clockwise.
5.
Remove blade and attaching hardware
(bolt, lock washer, hardened washer).
NOTE:
Remove the blade adapter and
check the key inside hub of blade adapter.
The key must be in good condition to work
properly. Replace adapter if damaged.
TO REPLACE
BLADE
1. Position the blade adapter on the en-
gine crankshaft.
Be sure key in adapter
and crankshaft
keyway are aligned.
2.
Position blade on the blade adapter.
13
IMPORTANT:
To ensure proper assembly,
center hole in blade must align with star
on blade adapter.
3. Be sure trailing edge of blade (opposite
sharp edge) is up toward the engine.
4. Install the blade bolt with the lock
washer and hardened washer into
blade adapter and crankshaft.
5. Use block of wood between blade and
lawn mower housing and tighten the
blade bolt, turning clockwise.
, The recommended
tightening
torque is
35-40 ft. Ibs.
IMPORTANT:
Blade bolt is heat treated.
If bolt needs replacing,
replace only with
approved bolt shown in the Repair Parts
section of this manual.
Blade
adapter
Key
Crankshaft
Lockwasher
Blade
\
Blade
bolt
Hardened
washer
Trailin/edge
retainer
TO SHARPEN
BLADE
NOTE: We do not recommend
sharp-
ening blade - but if you do, be sure the
blade is balanced.
An unbalanced
blade
will cause eventual damage to lawn
mower or engine.
, The blade can be sharpened with a file
or on a grinding wheel. Do not attempt
to sharpen while on the mower.
, To check blade balance, you will need
a 5/8" diameter steel bolt, pin, or a cone
balancer.
(When using a cone balancer,
follow the instructions supplied with it.)
NOTE:
Do not use a nail for balancing
blade. The lobes of the center hole may
appear to be centered, but are not.
, Slide blade on to an unthreaded
portion
of the steel bolt or pin and hold the
bolt or pin parallel with the ground.
If
blade is balanced,
it should remain in a
horizontal
position.
If either end of the
blade moves downward,
sharpen the
heavy end until the blade is balanced.
Center hole
5/8" bolt or pin
Blade
Publicidad
