HK Audio LINEAR 9 Serie Manual página 4

LINEAR 9 1.0
1 General Information
Thru
6
Unpacking and Inventorying
Ethernet
7
Data
When you first unpack your LINEAR 9 speaker cabinet, take a quick
inventory to make sure it comes complete with the manual and Powercon
In
mains cable.
2 Connectors and Controls
Input
4
1
5
DSP Out
LINEAR 9 210 LTA • LINEAR 9 110 XA • LINEAR 9 112 XA
4
L
1
LINEAR 9 iA
Input
4
112 XA
R
1
MADE IN GERMANY
5
DSP Out
Caution: Risk of electric shock! Do not open!
LINEAR 9 118 Sub A • LINEAR 9 118 Sub BA
Refer servicing to qualified service personnel.
Attention: Risque de choc élèctrique –
ne pas ouvrir!
●
1
Input
This XLR/ 1/4" (6.35 mm) combo jack provides a balanced input for analog
signals.
• The mid/high units have one input channel.
• The two subwoofers have two inputs, one each for the left and right
HK Audio is a brand of Stamer Musikanlagen GmbH
Magdeburger Str. 8 • 66606 St. Wendel • Germany
signals. The two channels are equal and merged post-preamp, so you can
use either one in mono mode.
●
2
Thru Power Mains Input
100-240 V~ 50-60 Hz
Use this parallel, balanced XLR output to send the signal routed into the
1 A @ 1/8 output power
LINEAR 7
Input through to other components. This output remains active even when
the electronic components are deactivated. The subwoofer has two of these
ports.
118 Sub A
4
MADE IN GERMANY
Power
Auto Sleep 1
On Off
2
8
3
Preset
4
Remote
Thru Gain
0 dB
2 3
10
+6 dB
Power
Auto Sleep
On Off
13
2
Thru Gain
0 dB
3
2
–6 dB +6 dB
Serial No.
Lock
●
3
Gain
Use this knob to adjust the input gain for the incoming signal.
• The control range for the mid/high units sweeps from –∞ (mute) to
+6 dB.
• The preamp Gain control on each of the two subwoofers addresses both
channels with a control range sweeping from -6 to +6 dB.
The center-notched 12 o'clock position is 0 dB in both cases.
Heads up: The Gain setting does not affect the signal sent to the DSP
Out.
●
4
Input/Limiter LED
This LED lights up green to indicate incoming signals and red to indicate
signal peaks. The LED briefly flashes red to tell you the Limiter is
responding to signal peaks. If it stays red, turn down the Gain knob.
●
5
DSP Out
This balanced XLR port taps the analog signal routed in via the Input. You
can use the internal DSP to process this signal. This way, the DSP Out can
serve as a network interface that lets you integrate another non-network-
enabled active speaker. In the factory default setup, the unprocessed
input signal is routed to the DSP Out regardless of the selected preset and
current position of the Gain knob.
Thru
6
Ethernet
7
Data
In
●
6
Ethernet In /Thru
Use the two Ethercon ports to integrate the speaker into a network. They
Input
accept RJ45 and Ethercon (NE8 MX, NE8 MX6, NE8 MC) plugs. Use the
4
Ethernet Thru port to forward the network signal.
1
Always use S/STP or S/FTP cables to shield against electromagnetic
interference. We recommend CAT6 cables. A separate manual explains
how to integrate and remotely control speakers in a network. You'll find it
posted on the LINEAR 9 downloads page at www.hkaudio.com. For a brief
description of the DSP functions, see section
5
●
7
Data
This LED lights up orange when data flows through the network connector.
DSP Out
LINEAR 9 iA
112 XA
MADE IN GERMANY
Power
Auto Sleep 1
On Off
2
8
3
Preset
4 Remote
Thru Gain
0 dB
2 3
+6 dB
●
8
Preset.